Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 106 — Epson AcuLaser C3000

Code: 106

Description: Firmware error
Remedy: 1 Does the error occur even when the power is turned Off and back On? Go to step 2. See if the problem recurs; if it does, go to step 2. 2 Harness Assy EEPROM connection check Check the connection of the P/J144 connector of the PWB EEPROM . Is P/J144 correctly connected? Go to step 3. Connect P/J144 correctly. 3 3.3V DC power supply to PWB EEPROM 1. Disconnect the P/J144 connector from the PWB EEPROM. 2. Measure the voltage between J144-2 <=> J144-1. Is there 3.3V DC between J144-2 <=> J144-1? Go to step 7. Go to step 4. 4 3.3V DC power supply to PWB Drive 1. Disconnect the P/J61 connector from the PWB Drive. 2. Measure the voltage between J61-6 <=> J61-5. Is there 3.3V DC between J61-6 <=> J61-5? Go to step 5. Go to FIP-DC . 5 Harness Assy EEPROM connection 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the connection of the P/J140 connector of the PWBA MCU & HVPS . Is P/J140 correctly connected? Go to step 6. Connect P/J140 correctly. 6 Harness Assy EEPROM continuity 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Disconnect the P/J140 connector from the PWBA MCU & HVPS . 3. Check the continuity for the following lines. J140-9 <=> J144-2 J140-10 <=> J144-1 Is there continuity in all lines between J140 <=> J144? Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) Replace the Harness Assy EEPROM . 7 PWB EE8 Harness Assy EEPROM connection 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the connection of the P/J140 connector of the PWBA MCU & HVPS . Is P/J140 correctly connected? Go to step 9. Connect P/J140 correctly. 9 Harness Assy EEPROM continuity 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Disconnect the P/J140 connector from the PWBA MCU & HVPS . 3. Check the continuity for the following lines. J140-7 <=> J144-4 J140-8 <=> J144-3 Is there continuity in all lines between J140 <=> J144? Go to step 10. Replace the Harness Assy EEPROM . 10 PWBA MCU & HVPS 1. Replace the PWBA MCU & HVPS with a new part. (Refer to Ch4-4.2.18.1) 2. Turn On the power. Does the problem still occur? Go to FIP-Noise . Problem solved.PROM 1. Replace the PWB EEPROM. (Refer to Ch4-4.2.15.8) 2. Turn On the power. Does the error code still appear? Go to step 8. Problem solved.

← Xem tất cả mã lỗi Epson AcuLaser C3000

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie