Code: 100
Description: ROS failure
Remedy: 1 Harness Assy ROS continuity check 1. Disconnect the P/J151 connector from the ROS Assy. (Refer to Ch4-4.2.14.1) 2. Disconnect the P/J15 connector from the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 3. Check the continuity in all lines between J15 <=>J151. Is the continuity normal between J15 <=> P151? Go to step 2. Replace the Harness Assy SOS . 2 PHD Assy 1. Install the new PHD Assy. 2. Turn On the power. Does the problem still occur? Go to step 3. Problem solved. 3 LD 5V DC circuit continuity (1) 1. Disconnect the P/J140 connector from the PWBA MCU & HVPS . 2. Check the continuity between P15-6 <=> P140-1. Is there continuity between P15-6 <=> P140-1? Go to step 4. Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 4 Harness Assy EEPROM , Harness Assy CRUM continuity Check the continuity for the following lines. J140-1 <=> P71-6/J71-1 <=> J710-6 J140-6 <=> P71-1/J71-6 <=> J710-1 Is there continuity in all lines? Go to step 5. Replace the harness with no continuity. 5 Power supply to 5V DC/24V DC 1. Remove the PHD Assy . 2. Measure the voltages at each terminal of the PWB Drive . P/J41-24 <=> P/J41-21/22 (5V DC) P/J41-17/18 <=> P/J41-19/20 (24V DC when interlock switch is on) Are the voltages between all terminals at the standard values? Go to step 6. Go to step 8. 6 Harness Assy DRV1 continuity 1. Disconnect the P/J41 connector from the PWB Drive . 2. Disconnect the P/J11 connector from the PWBA MCU & HVPS . 3. Check the continuity for the following lines. J41-17/18 <=> J11-24/23 J41-19/20 <=> J11-22/21 J41-24 <=> J11-17 J41-23 <=> J11-18 J41-21/22 <=> J11-20/19 Is there continuity in all lines? Go to step 7. Replace the Harness Assy DRV1 . 7 PWBA MCU & HVPS continuity 1. Disconnect the P/J15 and P/J140 connector from the PWBA MCU & HVPS. 2. Check the continuity for the following lines. P11-23/24 <=> P15-4 P11-17 <=> P15-7 <=> P140-6 P/J15-6 <=> P/J1401 Is there continuity in all circuits? Go to step 10. Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 8 PWB Drive continuity 1. Disconnect the P/J60 and P/J61 connector from the PWB Drive. 2. Check the continuity for the following lines. P60-1 <=> P41-17/18 (Press the interlock switch) P61-8 <=> P41-24 Is there continuity in all circuits? Go to step 9. Replace the PWB Drive. (Refer to Ch4-4.2.18.5) 9 Harness Assy 24V , Harness Assy LVNC continuity 1. Disconnect the P/J163 and P/J165 connector from the LVPS . 2. Check the continuity for the following lines. J163-1 <=> J60-1 J165-1 <=> J61-8 Is there continuity in all lines? Go to FIP-DC . Replace the harness with no continuity.