Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 59.XY — HP Color LaserJet 9500

Code: 59.XY

Display: 59.XY PRINTER ERROR
Description: The printer detects a motor that fails to turn or fails to turn at speed.
X description: 0 = motor error (not possible for the HP color LaserJet 9500) 1 = motor startup error 2 = motor rotation error 3 = fuser motor startup error 4 = fuser motor rotation error 5 = image drum motor startup error 6 = image drum motor rotation error 8 = developer motor failure 9 = ITB motor startup error A = ITB motor rotation error D = registration motor starting error E = registration motor rotation error Note 59.XY errors with X = A, D, or E noted in the log appear as 59.10.00, 59.13.00, and 59.14.00 respectively (59.XX.YY), where XX is a decimal conversion of the hexadecimal control panel display error.
Note Print cartridge motor errors are indicated as REMOVE AND SHAKE <COLOR> CARTRIDGE. Y description 0 = no color K = black C = cyan M = magenta Y = yellow
Remedy: Note If turning the printer off and on again does not resolve the 59.00 or 59.A0 error, remove and reinstall the image transfer cleaner.
• Print cartridge motor errors (remove and shake)
There are no 59 errors associated with the print cartridge motor errors. When the engine reports a fail to rotate for these motors, the error REMOVE AND SHAKE <COLOR> CARTRIDGE appears. 1 Remove and check the indicated print cartridge. Check the engine for damaged drive linkages. 2 Gently shake the print cartridge, reseat it, and turn the printer on. 3 Turn the printer off, and then turn the printer on again to clear the error. 4 Use the hardware diagnostic tools from the control panel to test each motor for correct functionality. 5 Check connector J1 on the lowvoltage power supply, J210 and J202 on the high-voltage power supply, J608 and J612 on the P driver PCA, and J806 on the T driver PCA. 6 Replace the print cartridge and the drive linkages if necessary. Note Make sure that the print cartridges, when stored, were not exposed to high temperatures. 7 Check connector 814 on the T driver PCA. 8 Check the color-appropriate connectors: • K: J3046 near the motor • C: J3047 near the motor • M: J3048 near the motor • Y: J3049 near the motor 9 Replace the T driver PCA. 10 Replace the DC controller PCA.
• Fuser motor errors
1 Turn the printer off, and then turn the printer on again to clear the error. 2 Remove and check the fuser for jammed media and damaged drive gears. 3 Perform a motor diagnostics test. 4 Check connector J3035 at the fuser motor and connector J116 on the DC controller PCA. 5 Check the fuser drive train for correct movement. Replace the fuser drive train if necessary. 6 Replace the fuser motor. 7 Replace the DC controller PCA.
• Image drum motor errors
1 Gently shake the print cartridge, reseat it, and turn the printer on. 2 Turn the printer off, and then turn the printer on again to clear the error. 3 Remove and check the indicated image drum, and check the engine for damaged drive linkages. 4 Reseat the image drum. 5 Replace the image drum and the drive linkages if necessary. 6 Check connector J1 on the lowvoltage power supply, J210 and J202 on the high-voltage power supply, J608 and J612 on the P driver PCA, and J806 on the T driver PCA. Note Make sure that the print cartridges, when stored, were not exposed to high temperatures. 7 Check FFC connectors J104 and J105 on the DC controller PCA, and connectors J601 and J616 on the P driver PCA (especially if the printer has been serviced recently). 8 Make sure that the FFC is centered and that it is completely inserted into the connector. Replace the FFC if it is damaged. 9 Check the color-appropriate connectors: • K: J610 and J613 on the P driver PCA, J701K for the encoder, and J3097 on the motor. • C: J607 and J614 on the P driver PCA, J701C for the encoder, and J3095 on the motor. • M: J605 and J615 on the P driver PCA, J701M for the encoder, and J3093 on the motor. • Y: J603 and J617 on the P driver PCA, J701Y for the encoder, and J3091 on the motor. 10 Check the process cartridge drive assembly encoders and motors for correct functionality. Replace the encoders and motors if necessary. 11 Replace the process cartridge drive assembly. 12 Replace the DC controller PCA. • Registration motor errors 1 Turn the printer off, and then turn the printer on again to clear the error. 2 Use the hardware diagnostic tools from the control panel to test the registration motor for correct functionality. 3 Check the registration motor drive linkages for correct functionality. Replace the linkages if necessary 4 Check connector J3036 at the registration motor and connector J117 on the DC controller PCA. 5 Replace the registration motor. 6 Replace the DC controller PCA.
• Developer motor errors
1 Turn the printer off, and then turn the printer on again to clear the error. 2 Remove and check the indicated image drum, and check the engine for damaged drive linkages. 3 Reseat the image drum and turn the printer on. 4 Use the hardware diagnostic tools from the control panel to test each motor for correct functionality. 5 Replace the image drum and the drive linkages if necessary. 6 Check connector J1 on the lowvoltage power supply, J210 and J202 on the high-voltage power supply, J608 and J612 on the P driver PCA, and J806 on the T driver PCA. 7 Check FFC connectors J104 and J105 on the DC controller PCA, and connectors J601 and J616 on the P driver PCA (especially if the printer has been serviced recently). 8 Make sure that the FFC is centered and that it is completely inserted into the connector. Replace the FFC if it is damaged. 9 Check the color-appropriate connectors: • K: J609 on the P driver PCA, and J3096 on the motor. • C: J606 on the P driver PCA, and J3094 on the motor. • M: J604 on the P driver PCA, and J3092 on the motor. • Y: J602 on the P driver PCA, and J3090 on the motor. 10 Check the process cartridge drive assembly encoders and motors for correct functionality. 11 Replace the process cartridge drive assembly. 12 Replace the DC controller PCA. • Registration motor error 1 Turn the printer off, and then turn the printer on again to clear the error. 2 Check the registration assembly for damage or jammed media. 3 Check the gear train on the registration drive assembly for correct functionality. 4 Use the hardware diagnostic tools from the control panel to test each motor for correct functionality. 5 Check connector J3036 on the registration motor, and connector J117 on the DC controller PCA. 6 Use the hardware diagnostic tools from the control panel to test each motor for correct functionality. 7 Check connector J3036 on the registration motor, and connector J117 on the DC controller PCA. 8 Replace the registration motor. 9 Replace the DC controller PCA.
• ITB motor error
1 Turn the printer off, and then turn the printer on again to clear the error. 2 Partially remove the ITB. 3 Turn the fly wheel on the right side to check the ITB for damage and correct movement. Check the drive linkages from the ITB motor for damage. Replace any damaged hardware. 4 Reseat the ITB and raise the green lever. 5 Use the hardware diagnostic tools from the control panel to test the ITB motor for correct functionality. 6 Remove and reseat the secondary transfer roller and the cleaning blade/toner collection bottle. 7 Check connector J1 on the lowvoltage power supply, J210 and J202 on the high-voltage power supply, J608 and J612 on the P driver PCA, and J806 on the T driver PCA. 8 PCA (especially if the printer was recently serviced). 9 Make sure that the FFC is centered and that it is completely inserted into the connector. Replace the FFC if it is damaged. 10 Check connector J3098 at the motor, and connector J611 on the P driver PCA. 11 Check FFC connector J104 on the DC controller PCA, and FFC connector J601 on the P driver. • T2 clutch error 1 Turn the printer off, and then turn the printer on again to clear the error. 2 Use the hardware diagnostic tools from the control panel to test each motor for correct functionality. 3 Remove and reseat the secondary transfer roller and the cleaning blade/toner collection bottle. 4 Check the secondary transfer assembly for damage or jammed media. 5 Check connector J3030 on the secondary transfer assembly, intermediate connector J3026, and connector J121 on the DC controller PCA. 6 Replace the secondary transfer assembly. 7 Replace the DC controller PCA.

← Xem tất cả mã lỗi HP Color LaserJet 9500

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie