Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 13.12.42 — HP Color LaserJet CM6040 MFP

Code: 13.12.42

Display: 13.12.42
Description: Finisher delay jam at booklet-making paperentry sensor (PI22) Occurs when booklet making function is selected and after the engine signals the finisher that it is delivering paper to the finisher. The booklet-making paper-entry sensor (PI22) is not activated within the expected time period after receiving the engine's delivery signal, suggesting that a paper jam has occurred somewhere between the output accessory bridge (IPTU) and sensor PI22.
Remedy: Control-panel diagnostics: M9 (Inlet Motor), SL5 (Inlet-Switch Solenoid) Signal generated from: PI22 (Booklet-Making Paper-Entry Sensor) Open the IPTU and the finisher top door and locate the media jam. Check the following items: • If media is found in the IPTU but has not reached the finisher entrance point, perform the following steps: • Remove and then reinstall the IPTU• Make sure that the connector is fully seated and that the IPTU is securely fastened. • If the error persists, replace the IPTU. • If media is jammed at the entrance point of the finisher, perform the following steps: • Verify that the finisher is securely fastened to the engine. • Make sure that the finisher and IPTU are correctly aligned. Adjust the finisher castors to obtain a uniform gap between the finisher and the engine. The engine-tofinisher gap must be the same at the bottom and the top so that the finisher is parallel to the engine. With the engine-to-finisher gap correct, make sure that the finisher paper path entry point is aligned with the IPTU exit point. • Check the finisher entry-point guides for damage. • Verify that the finisher rollers are turning before the media leaves the IPTU. If the rollers are not turning, test motor M9 by using the finisher component test from the controlpanel display. If the motor does not activate during the test, check the connectors for motor M9 (inlet motor). Make sure that connector J705 is fully seated on the stacker controller PCA. If the error persists, replace motor M9 or the saddle-paper-feeder assembly for the type finisher you are working on. Only if the error persists and none of the previous steps correct the problem, replace the stacker controller PCA. • If media is found in the finisher but has not reached sensor PI22, perform the following steps: • Check the upper and lower guides and rollers in the paper path for damage. • Make sure that the media-diverter gate (saddle-stitch flapper) is not blocking the paper path. • Test solenoid SL5 (inlet-switch solenoid) by using the finisher component test from the controlpanel display. SL5 should be opening and closing the mediadiverter gate (saddle stitch flapper). • If media is found in the finisher cover sensor PI22 (the sensor is not detecting the media), perform the following steps: • Check the sensor for obstructions. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body• Make sure that the lower end of the flag is not damaged and is correctly positioned to activate the sensor. • Make sure that the sensor is securely fastened to the chassis. • Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. • Verify that the wiring at the sensor is not damaged and that the intermediate connectors between the sensor and connector J21 on the saddle-stitcher controller PCA are fully seated• Replace the sensor if necessary. If PI22 is determined to be the failure point, replace the saddle-paper-feeder assembly, which includes PI22. • Only if the error persists and none of the previous steps correct the problem, replace the saddlestitcher controller PCA.

← Xem tất cả mã lỗi HP Color LaserJet CM6040 MFP

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie