Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 50.WX.YZ — HP LaserJet Enterprise 500 MFP M525c

Code: 50.WX.YZ

Display: 50.WX.YZ Fuser error
Description: The product experienced a fuser error. • W = fuser error code • X = fuser mode • 0: Photo paper 1, 2, 3, Designated paper 2, 3, or NA, typed or AutoSense • 1: AutoSense (Normal special case distinguished from typed Normal) • 2: Normal, typed (not AutoSense) • 3: Light paper 1, 2, or 3, typed or AutoSense • 4: Heavy paper 1, typed or AutoSense • 5: Heavy paper 2, typed or AutoSense • 6: Heavy paper 3, typed or AutoSense • 7: Glossy paper 1, typed or AutoSense • 8: Glossy paper 2, typed or AutoSense • 9: Glossy paper 3, typed or AutoSense • A: Glossy film, typed or AutoSense • B: Transparency, typed or AutoSense • C: Label • D: Envelope1, Envelope2, or Envelope3 • E: Rough (designated paper 1), typed or AutoSense • F: Reserved for future fuser mode • Y = previous product sleep state • Z = next product sleep state • 0: Printing • 1: Standby level 1 (no temperature control) • 2: Standby level 2 (high temperature control) • 3: Standby level 3 (middle temperature control) • 4: Standby level 4 (low temperature control) • 5: Middle sleep • 6: Deep sleep • F: Off
Remedy: W = A: High fuser temperature 2: 1. Remove and then reseat the fuser. Make sure there is no residual paper in the fuser. Make sure the product is not located in front of a vent or window where cool air may interfere with the ability of the fuser to heat up. 2. Check the product power source. Make sure the power source meets product requirements. Make sure this is the only device using the circuit. 3. Check the connector between the fuser and the product. If it is damaged, replace the fuser. 4. If this product was previously serviced, check the connector on the DC controller PCA. 5. If the error persists, replace the fuser. W = B: High fuser temperature 3: 1. Remove and then reseat the fuser. Remove any residual paper in the product. 2. Check the paper type setting using the product menus and in the print driver. Making sure that they match and are correct for the type of paper being used. 3. If this product was previously serviced, check the connector on the DC controller PCA. 4. If the error persists, replace the fuser. W = 1, Low fuser error temperature error: 1. Remove and then reseat the fuser. 2. Check the paper type setting using the product menus and in the product driver. Make sure that they match and are correct for the type of paper being used. 3. If this product was previously serviced, check the connector on the DC controller PCA. 4. If the error persists, replace the fuser. W = 2, Fuser warm-up failure: 1. Reconnect the connector between the fuser and the DC controller PCA. 2. Turn the product off. Remove the fuser, and then reinstall it. 3. Replace the fuser wire harness. 4. If the error persists, replace the fuser. W = 3, High fuser temperature 1: 1. Remove and then reseat the fuser. 2. Check the paper type setting using the product menus and in the product driver. Make sure that they match and are correct for the type of paper being used. 3. If this product was previously serviced, check the connector on the DC controller PCA. 4. If the error persists, replace the fuser. W = 4, Fuser power supply driving circuit error: 1. Remove and then reseat the fuser. 2. If this product was previously serviced, check the connector on the DC controller PCA. 3. If the error persists, replace the fuser. W = 6, Open fuser, breaking of a heater wire: 1. Check the power source. Make sure the power source meets product requirements. 2. If this product was previously serviced, check the connector on the DC controller PCA. 3. If the error persists, replace the low-voltage power supply. W = 7, Fuser pressure-release mechanism failure: 1. Remove and then reseat the fuser. Make sure there is no residual paper in the fuser. 2. Check the fuser pressure-release sensor flag. If it is damaged, replace the fuser. 3. Use the manual sensor test to verify that the fuser pressure-release sensor is properly functioning. If it is not, replace the fuser. 4. Use the fuser pressure-release drive test in the component test to verify that the fuser motor is properly functioning. If it is not, replace the fuser motor. 5. If this product was previously serviced, check the connector on the DC controller PCA. 6. If the error persists, replace the fuser. W = 8, Low fuser temperature 2: 1. Remove and then reseat the fuser. Make sure there is no residual paper in the fuser. Make sure the product is not located in front of a vent or window where cool air may interfere with the ability of the fuser to heat up. 2. Check the product power source. Make sure the power source meets product requirements. Make sure this is the only device using the circuit. 3. Check the connector between the fuser and the product. If it is damaged, replace the fuser. 4. If this product was previously serviced, check the connector on the DC controller PCA. 5. If the error persists, replace the fuser. W = 9, High fuser temperature 2: 1. Remove and then reseat the fuser. Make sure there is no residual paper in the fuser. Make sure the product is not located in front of a vent or window where cool air may interfere with the ability of the fuser to heat up. 2. Check the product power source. Make sure the power source meets product requirements. Make sure this is the only device using the circuit. 3. Check the connector between the fuser and the product. If it is damaged, replace the fuser. 4. If this product was previously serviced, check the connector on the DC controller PCA. 5. If the error persists, replace the fuser.

← Xem tất cả mã lỗi HP LaserJet Enterprise 500 MFP M525c

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie