Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 13.B2.Dz — HP LaserJet M630z Enterprise MFP

Code: 13.B2.Dz

Display: 13.B2.Dz Jam in top cover
Description: Paper Delay Jam at Registration Top Paper Delay jam at Registration area?fs TOP sensor (PS103) (Late arriving at sensor) 13.B2.Dz (?gz?h being the tray which the paper was fed from: Tray 1-6) An error code appears on the control panel as 13.B2.D(1-6). Paper Jam. • 13.B2.D1 This jam occurs when the paper is picked from Tray 1 and SP103 is not triggered. • 13.B2.D2 This jam occurs when the paper is picked from Tray 2 and PS102 is triggered, but PS103 is not triggered. • 13.B2.D3: This jam occurs when the paper is picked from Tray 3 and SR4 is triggered, but PS103 is not triggered. • 13.B2.D4: This jam occurs when the paper is picked from Tray 5 and SR8 is triggered, but PS103 is not triggered. • 13.B2.D5: This jam occurs when the paper is picked from Tray 5 and SR12 is triggered, but PS103 is not triggered. Call Out 1 - PS103 Top Sensor Call Out 2 - PS102 Prefeed Sensor NOTE: PS102 and PS103 are not replaceable or removable.
Remedy: If paper was fed from Tray 1 (MP) (13.B2.D1): Probable cause is a tray 1 misfeed (mispick). Replace Tray 1 feed rollers and make sure paper is properly identified in control panel. If paper was fed from Trays 2-5 or the duplexer: The error indicates that the paper did activate PS102 (Prefeed Sensor) but did not reach PS103 (TOP Sensor). Before beginning repair: IF printer is found still signaling error: • Before opening the printer, do a control panel test to see what sensors are activated and write them down. (Especially note the states of PS101, PS102, PS103, PS107, and PS907). • Note locations or any paper found in paper path and especially those found just before or after PS103 in the registration area. Run a set of internal pages: • Are all of the 13.B2.Dx errors from the same paper tray • How often are they occurring Try to recreate the error: • Using the Event log, determine which tray(s) the error is occurring from then run single sided copies from that tray to try to recreate the error. • Replace the feed, Pickup and separation rollers for paper trays with errors. • Adjust the paper tray guides and load the paper according to procedure stated at the end of this document. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. • Try to recreate the error again, using that same tray. • If error still occurs, then continue to the troubleshooting section of this document before removing the jammed paper from the printer. 1. 1. Open the top cover and MP door and remove the toner cartridge to expose the paper path at the registration area. Inspect the paper path, take note as to where any paper and the paper’s leading edge is located and if simplex or duplex job was being run. Also inspect the leading edge of the paper for any signs of the paper catching on something. 2. If the leading edge of the paper closest to the registration assembly is past PS103 then the problem is most likely with the sensing of the paper with PS103 3. Use Manual sensor test to verify consistent operation of the Registration TOP sensor. Administration Troubleshooting Diagnostic Test Manual Sensor Test Scroll down until PS103 TOP is displayed When activating PS103 sensor, watch the control panel display for the sensor state to change from green to clear or clear to green. I might take a few seconds to change as you toggle sensor flag.

← Xem tất cả mã lỗi HP LaserJet M630z Enterprise MFP

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie