Code: SVC C7
Description: Process timing error
Causes: Synchronization signal from main motor is not detected.
Remedy: 1 Turn printer off and remove right cover. Open top cover and override top cover interlock switch. Restart printer and observe main motor and photodeveloper cartridge OPC belt. Does main motor attempt to turn but OPC belt will not rotate? Replace photodeveloper cartridge. Note: Photo-developer cartridge is a customer ordered supply. Go to step 2.
2 Observe main motor and fuser. Does main motor attempt to turn but fuser will not? Replace fuser assembly. . Note: Fuser is a customer ordered supply. Go to step 3.
3 Are there any unusual noises around main motor before error posts? Replace main motor. . Go to step 4. Go to step 5.
4 Does noise go away? Problem solved. Go to step 5.
5 Is cable properly connected to main motor? Go to step 6. Properly connect cable. Retest printer. If error clears, problem solved, otherwise go to step 6.
6 If waste toner bottle is removed, reinsert it. Ensure rear cover assembly cover is shut. Override top and front cover interlock switches. Reconnect operator panel. Turn printer on. Allow printer to run until error posts. Disconnect connector from main motor and check the following on disconnected cable connector: Pin 4 to pin 5—24VDC Pin 6 to pin 5—24VDC Pin 10 to pin 5—5VDC Are voltages present? Replace main motor.Go to step 9. Go to step 7.
7 Remove engine controller board board shield. for steps to remove engine controller board shield. Disconnect MCN5 from engine controller board. Check for continuity and shorted pins on cable that connects MCN5 to main motor. Is cable okay? Go to step 8. Replace cable. Retest printer. If error clears, problem solved, otherwise go to step 8.
8 Disconnect cable from engine controller board POCN. Check the following on disconnected cable connector: Pin 21 to pin 22—24VDC Pin 13 to pin 14—5VDC Are voltages present? Replace engine controller board. . Go step 9. Replace cable that connects ACN1 on LVPS to POCN on engine controller board. Remove RIP board cage to gain access to cable. . Go to step 9.
9 Reassemble and retest printer. Does error clear? Problem solved. Contact next level of maintenance
2 Observe main motor and fuser. Does main motor attempt to turn but fuser will not? Replace fuser assembly. . Note: Fuser is a customer ordered supply. Go to step 3.
3 Are there any unusual noises around main motor before error posts? Replace main motor. . Go to step 4. Go to step 5.
4 Does noise go away? Problem solved. Go to step 5.
5 Is cable properly connected to main motor? Go to step 6. Properly connect cable. Retest printer. If error clears, problem solved, otherwise go to step 6.
6 If waste toner bottle is removed, reinsert it. Ensure rear cover assembly cover is shut. Override top and front cover interlock switches. Reconnect operator panel. Turn printer on. Allow printer to run until error posts. Disconnect connector from main motor and check the following on disconnected cable connector: Pin 4 to pin 5—24VDC Pin 6 to pin 5—24VDC Pin 10 to pin 5—5VDC Are voltages present? Replace main motor.Go to step 9. Go to step 7.
7 Remove engine controller board board shield. for steps to remove engine controller board shield. Disconnect MCN5 from engine controller board. Check for continuity and shorted pins on cable that connects MCN5 to main motor. Is cable okay? Go to step 8. Replace cable. Retest printer. If error clears, problem solved, otherwise go to step 8.
8 Disconnect cable from engine controller board POCN. Check the following on disconnected cable connector: Pin 21 to pin 22—24VDC Pin 13 to pin 14—5VDC Are voltages present? Replace engine controller board. . Go step 9. Replace cable that connects ACN1 on LVPS to POCN on engine controller board. Remove RIP board cage to gain access to cable. . Go to step 9.
9 Reassemble and retest printer. Does error clear? Problem solved. Contact next level of maintenance