Code: 910
Description: Developing motor (DM) error
Remedy: 1 Are there any unusual noises heard around developer motor or developer drive assembly before error posts? Replace toner cartridge (customer ordered supply). Go to step 2. Go to step 4.
2 Does noise go away? Problem solved. Replace developer motor and developer drive assembly. Go to step 3.
3 Does noise go away? Problem solved. Go to step 4.
4 Turn printer off and remove right cover. Is cable properly connected to developer motor? Go to step 5. Properly connect cable. Retest printer. If error clears, problem solved, otherwise go to step 5.
5 If waste toner bottle is removed, reinsert it. Ensure rear cover assembly is shut. Override top and front cover interlock switches. For location, Reconnect operator panel. Turn printer on. Allow printer to run until error posts. Disconnect connector from developer motor and check the following on disconnected cable connector: Pin 4 to pin 5—24VDC Pin 6 to pin 5—24VDC Pin 10 to pin 5—5VDC Are voltages present? Replace developer motor. Go to step 8 Go to step 6.
6 Remove I/O board shield. Disconnect DCN11 from I/O board. Check for continuity and shorted pins on cable that connects DCN11 to developer motor. Is cable okay? Go to step 7. Replace cable. Retest printer. If error clears, problem solved, otherwise go to step 7.
7 Disconnect cable from DCN13 on I/O board. Check the following on disconnected cable connector: Pin 1 to pin 2—24VDC Pin 9 to pin 12—5VDC Are voltages present? Replace I/O board. Go step 8. Replace cable that connects ACN1 on LVPS to DCN13 on I/O board. Remove RIP board cage to gain access to cable. Go to step 8.
8 Reassemble and retest printer. Does error clear? Problem solved. Go to step 9.
9 Check cable that connects engine controller board connector I2CN to I/O board connector DCN3 for continuity and pin shorts. Is cable okay? Replace engine controller board. Replace cable.
2 Does noise go away? Problem solved. Replace developer motor and developer drive assembly. Go to step 3.
3 Does noise go away? Problem solved. Go to step 4.
4 Turn printer off and remove right cover. Is cable properly connected to developer motor? Go to step 5. Properly connect cable. Retest printer. If error clears, problem solved, otherwise go to step 5.
5 If waste toner bottle is removed, reinsert it. Ensure rear cover assembly is shut. Override top and front cover interlock switches. For location, Reconnect operator panel. Turn printer on. Allow printer to run until error posts. Disconnect connector from developer motor and check the following on disconnected cable connector: Pin 4 to pin 5—24VDC Pin 6 to pin 5—24VDC Pin 10 to pin 5—5VDC Are voltages present? Replace developer motor. Go to step 8 Go to step 6.
6 Remove I/O board shield. Disconnect DCN11 from I/O board. Check for continuity and shorted pins on cable that connects DCN11 to developer motor. Is cable okay? Go to step 7. Replace cable. Retest printer. If error clears, problem solved, otherwise go to step 7.
7 Disconnect cable from DCN13 on I/O board. Check the following on disconnected cable connector: Pin 1 to pin 2—24VDC Pin 9 to pin 12—5VDC Are voltages present? Replace I/O board. Go step 8. Replace cable that connects ACN1 on LVPS to DCN13 on I/O board. Remove RIP board cage to gain access to cable. Go to step 8.
8 Reassemble and retest printer. Does error clear? Problem solved. Go to step 9.
9 Check cable that connects engine controller board connector I2CN to I/O board connector DCN3 for continuity and pin shorts. Is cable okay? Replace engine controller board. Replace cable.