Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 421.13, 421.15 — Lexmark C6160

Code: 421.13, 421.15

Description: 421.13 The sensor (staple finisher front tamper home) was not covered at the specified time. 421.15 The sensor (staple finisher front tamper home) was not cleared within the specified time.
Remedy: Step 1 a Clear the following areas of any jams or obstructions: • Jam door • Finisher bin • Paper path • Staple finisher tamper area b Move the tampers from one side to another, and then back to the original position. c Reset the printer, and then reseat the staple finisher. Does the problem remain? Go to step 2. The problem is solved. Step 2 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Motor tests b Find the motor (Tamper front and rear), and then touch Start. Does the motor run? Go to step 4. Go to step 3. Step 3 a Check the motor (staple finisher front tamper home) for proper installation and damage, and replace if necessary. See “Motor (staple finisher tamper) removal”. b Reseat the connector on both ends of the motor. Does the problem remain? Go to step 4. The problem is solved. Step 4 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Sensor tests > Staple Finisher > Tamper sensors b Find the sensor (Front tamper home). Does the sensor status change while toggling the sensor? Go to step 6. Go to step 5. Step 5 a Check the sensor (staple finisher front tamper home) for proper installation and damage, and replace if necessary. See “Sensor (staple finisher tamper position) removal”. b Reseat the connector on both ends of the sensor. Does the problem remain? Go to step 6. The problem is solved. Step 6 Check the cables for cuts or damage, and replace if necessary. Does the problem remain? Go to step 7. The problem is solved. Step 7 a Move the tampers from one side to another, and then make sure that the tamper area is free from any obstructions. b Check the tampers for any damages, and replace if necessary. See “Staple finisher tamper removal”. Does the problem remain? Go to step 8. The problem is solved. Step 8 a Check the tamper belt holder for damages, and replace if necessary. See “Staple finisher tamper removal”. b Check the tamper belt holder for proper installation. Make sure that the front tamper belt is properly aligned. Does the problem remain? Go to step 9. The problem is solved. Step 9 a Check the staple finisher tamper belt for damage, and replace if necessary. See “Staple finisher tamper belts removal”. b Check the belts for proper installation. Make that the spring and the holder are properly aligned. Does the problem remain? Go to step 10. The problem is solved. Step 10 a Check the stapler finisher tamper pulley gears for damage, and replace if necessary. See “Staple finisher tamper pulley gear removal”. b Make sure that the gears are properly installed. Does the problem remain? Go to step 11. The problem is solved. Step 11 Reseat all connectors in the staple finisher controller board, and then reset the printer. Does the problem remain? Go to step 12. The problem is solved. Step 12 Replace the controller board. See “Staple finisher controller board removal”. Does the problem remain? Contact the next level of support. The problem is solved.

← Xem tất cả mã lỗi Lexmark C6160

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie