Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 280.11...284.15 — Lexmark CS720de

Code: 280.11...284.15

Description: 280.11 The paper remains detected at the sensor (media pres280.13 The sensor (media present) did not detect the paper. 280.15 The paper remains detected at the sensor (media present) during a job. 281.11 The paper remains detected at the sensor (pick) after the printer is turned on. 281.13 The sensor (pick) did not detect the paper. 281.15 The paper remains detected at the sensor (pick) during a job. 283.11 The paper remains detected at the sensor (trail) after the printer is turned on. 283.13 The sensor (trail) did not detect the paper. 283.15 The paper remains detected at the sensor (trail) during a job. 284.11 The paper remains detected at the sensor (1st scan) after the printer is turned on. 284.13 The sensor (1st scan) did not detect the paper. 284.15 The paper remains detected at the sensor (1st scan) during a job.ent) after the printer is turned on.
Remedy: Step 1 Resend the scan job. Does the problem remain? Go to step 2. The problem is solved. Step 2 Check the paper path for paper jams and fragments. Is the paper path free of fragments and debris? Go to step 4. Go to step 3. Step 3 Remove the paper jams and fragments. Does the problem remain? Go to step 4. The problem is solved. Step 4 Check if the paper feeds into the ADF. Does the paper feed into the ADF? Go to step 6. Go to step 5. Step 5 Perform the ADF feed error service check. See “ADF feed errors service check”. Does the problem remain? Go to step 6. The problem is solved. Step 6 Check if the paper has a bent or curled leading edge. Does the paper have a bent or curled leading edge? Go to step 7. Go to step 10. Step 7 Replace the paper, and then resend the scan job. Does the problem remain? Go to step 8. The problem is solved. Step 8 Check if the paper is damp or heavy. Is the paper damp or heavy? Go to step 9. Go to step 10. Step 9 Replace the paper, and then resend the scan job. Does the problem remain? Go to step 10. The problem is solved. Step 10 a Enter the Diagnostics menu, and then navigate to: Scanner diagnostics > Motor tests > ADF pick b Touch Start. c Enter the Diagnostics menu, and then navigate to: Scanner diagnostics > Motor tests > ADF transport d Touch Start. Does each motor run? Go to step 12. Go to step 11. Step 11 Reseat the ADF cable on the JADF1 connector on the controller board. Does the problem remain? Go to step 12. The problem is solved. Step 12 a Enter the Diagnostics menu, and then navigate to: Scanner diagnostics > Sensor tests b Find the following sensors: 1 Sensor (ADF media present) 2 Sensor (ADF 1st scan) 3 Sensor (ADF trail) 4 Sensor (ADF duplex) Does the status of each sensor change while toggling the sensors? Go to step 16. Go to step 13. Step 13 Check the sensor for dirt and debris. Is the sensor free of dirt and debris? Go to step 16. Go to step 14. Step 14 Clean the sensor. Does the problem remain? Go to step 15. The problem is solved. Step 15 Check if the actuator is stuck or damaged. Is the actuator stuck or damaged? Go to step 18. Go to step 16. Step 16 Reseat the ADF cable on the JADF1 connector on the controller board. Does the problem remain? Go to step 17. The problem is solved. Step 17 Check the following pins of the JADF1 connector on the controller board if the values are as shown: a Pins 14 and 16 are +25V. b Pins 15 and 22 are +3V. c Pins 17, 18, and 23 are GND. Are the values approximately correct? Contact the next level of support. Go to step 18. Step 18 Replace the ADF. See “ADF removal”. Does the problem remain? Contact the next level of support. The problem is solved.

← Xem tất cả mã lỗi Lexmark CS720de

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie