Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 429.11...429.15 — Lexmark CX820

Code: 429.11...429.15

Description: 429.11 The media remains detected by the sensor (staple finisher staple unit paper present) after power-on. 429.13 The sensor (staple finisher staple unit paper present) does not detect the media within the specified time. 429.14 The sensor (staple finisher staple unit paper present) was not covered by the media during stapling. 429.15 The media does not leave the sensor (staple finisher staple unit paper present) within the specified time.
Remedy: Step 1 a Clear the paper path of any jams or obstructions. b Reset the printer, and then reseat the staple finisher. Does the problem remain? Go to step 2. The problem is solved. Step 2 Check the sensor (staple finisher staple unit paper present) for proper operation. a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Sensor tests > Staple finisher > Compile and staple section b Find the sensor (Staple unit paper presence). Does the sensor status change while toggling the sensor? Go to step 4. Go to step 3. Step 3 a Check the sensor (staple finisher staple unit paper present) for proper installation and damage, and replace if necessary. See “Sensor (staple finisher staple unit paper present) removal”. b Reseat the connector on both ends. Does the problem remain? Go to step 4. The problem is solved. Step 4 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Sensor tests > Staple finisher > Transport and exit section b Find the sensor (Upper exit roller). Does the sensor status change while toggling the sensor? Go to step 6. Go to step 5. Step 5 a Check the sensor for proper installation and damage, and replace if necessary. See “Sensor (staple finisher upper exit roller) removal”. b Reseat the connector on both ends. Does the problem remain? Go to step 6. The problem is solved. Step 6 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Motor tests b Find the motor (Exit assembly), and then touch Start. Does the motor run? Go to step 8. Go to step 7. Step 7 a Check the motor for proper installation and damage, and replace if necessary. See “Motor (staple finisher upper exit roller) removal”. b Reseat the connector on both ends. Does the problem remain? Go to step 8. The problem is solved. Step 8 Check the cables for cuts or damage, and replace if necessary. Does the problem remain? Go to step 9. The problem is solved. Step 9 a Check the staple finisher upper paper guide for proper installation and damage, and replace if necessary. See “Staple finisher aligner paddle and upper paper guide removal”. b Check the paper guide bail for proper installation and damage, and replace if necessary. Does the problem remain? Go to step 10. The problem is solved. Step 10 a Check the staple finisher front upper exit roller position gears for proper installation and damage, and replace if necessary. See “Staple finisher front upper position exit roller gears removal”. b Check the actuator and lever for proper installation and damage, and replace if necessary. c Make sure that the springs are properly installed. d Check if the roller goes up and down after moving the gears. e Lift the gear to check if the actuator covers the sensor. Does the problem remain? Go to step 11. The problem is solved. Step 11 a Check the staple finisher rear upper exit roller position gears and lever for proper installation and damage, and replace if necessary. See “Staple finisher rear upper position exit roller gears removal”. b Check if the roller goes up and down after moving the gears. Does the problem remain? Go to step 12. The problem is solved. Step 12 a Check the staple finisher upper exit roller for proper installation and damage, and replace if necessary. See “Staple finisher upper exit roller removal”. b Check if the roller goes up and down after moving the gears. Does the problem remain? Go to step 13. The problem is solved. Step 13 Check the controller board for damage, and replace if necessary. See “Staple finisher controller board removal”. Does the problem remain? Go to step 14. The problem is solved. Replace the controller board. See “Staple finisher controller board removal”. Does the problem remain? Contact the next level of support. The problem is solved.

← Xem tất cả mã lỗi Lexmark CX820

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie