Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 423.13...423.55 — Lexmark CX860de

Code: 423.13...423.55

Description: 423.13 The sensor (staple finisher upper exit roller) was not covered within the specified time. 423.15 The sensor (staple finisher upper exit roller) remains covered after the specified time. 423.51 The motor (staple finisher upper exit roller) does not turn off. 423.54 The motor (staple finisher upper exit roller) fails to achieve expected speed. 423.55 The motor (staple finisher upper exit roller) runs too fast.
Remedy: Step 1 a Clear the paper path of any jams or obstructions. b Reset the printer, and then reseat the staple finisher. Does the problem remain? Go to step 2. The problem is solved. Step 2 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Sensor tests > Staple Finisher > Transport and exit section b Find the sensor (Upper exit roller). Does the sensor status change while toggling the sensor? Go to step 5. Go to step 3. Step 3 Check the sensor (staple finisher upper exit roller) for misalignment and damage. Is the sensor properly installed and free of damage? Go to step 5. Go to step 4. Step 4 Reinstall or replace the sensor. See “Sensor (staple finisher upper exit roller) removal”. Does the motor run? Go to step 5. The problem is solved. Step 5 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Motor tests b Find the motor (Upper exit roller), and then touch Start. Does the motor run? Go to step 8. Go to step 6. Step 6 Check the motor (staple finisher upper exit) for misalignment and damage. Is the motor properly installed and free of damage? Go to step 8. Go to step 7. Step 7 Reinstall or replace the motor. See “Motor (staple finisher upper exit roller) removal”. Does the problem remain? Go to step 8. The problem is solved. Step 8 Check the cables for cuts or damages, and replace if necessary. Does the problem remain? Go to step 9. The problem is solved. Step 9 a Check the front upper exit roller position gears, actuator, and lever for damage. b Check the gears for proper installation and alignment. c Check the spring for proper installation. d Move the gears, and then check if the roller moves up and down. e Check if the actuator can cover the sensor. Does the problem remain? Go to step 10. The problem is solved. Step 10 Replace the staple finisher front upper exit roller position gears. See “Staple finisher front upper position exit roller gears removal”. Does the problem remain? Go to step 11. The problem is solved. Step 11 a Check the rear upper exit roller position gears, actuator, and lever for damage. b Check the gears for proper installation and alignment. c Check the spring for proper installation. d Move the gears, and then check if the roller moves up and down. e Check if the actuator can cover the sensor. Does the problem remain? Go to step 12. The problem is solved. Step 12 Replace the staple finisher rear upper exit roller position gears. See “Staple finisher rear upper position exit roller gears removal”. Does the problem remain? Go to step 13. The problem is solved. Step 13 a Check the staple finisher upper exit roller for proper installation. b Check the roller for wear or damage, and replace if necessary. See “Staple finisher upper exit roller removal”. c Check if the roller can move up and down. Does the problem remain? Go to step 14. The problem is solved. Step 14 Reseat all cable connectors in the controller board, and then reset the printer. Does the problem remain? Contact the next level of support. The problem is solved.

← Xem tất cả mã lỗi Lexmark CX860de

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie