Code: 243.31, 243.43, 243.91
Description: 243.31 2500.sheet tray: The paper remains detected at the sensor (tray 3 feed) after the printer is turned on. 243.43 2500.sheet tray: The paper remains detected at the sensor (tray 3 transport) during a print job. 243.91 2500.sheet tray: The paper remains detected at the sensor (tray 3 transport) after the printer is turned on.
Remedy: Step 1 a Enter the Diagnostics menu, and then navigate to: EVENT LOG > Display Log b Check the last digits of the error codes. Do most of the recent error codes end with a 1? (Example: 241.11, 200.91) Go to step 2. Go to step 7. Step 2 Make sure that the 2500-sheet tray feed paper path, including the sensors, are free of debris or dust. Does the problem remain? Go to step 3. The problem is solved. Step 3 Check the sensor (2500-sheet tray feed) for damage. Is it free of damage? Go to step 4. Go to step 6. Step 4 Enter the Diagnostics menu, and then navigate to: SENSOR TESTS > 2500-Sheet Tray Sensor Tests Does the sensor status change while toggling the sensor? Go to step 13. Go to step 5. Step 5 a Reseat the 2500-sheet tray feed sensor cable. b Check the cable for damage, and replace if necessary. Does the problem remain? Go to step 6. The problem is solved. Step 6 Replace the sensor (2500-sheet tray feed). See gSensor (2500.sheet tray feed) removalh. Does the problem remain? Go to step 7. The problem is solved. Step 7 a Enter the Diagnostics menu, and then navigate to: INPUT TRAY TESTS > Feed Tests > Tray 3 b Observe the movement and position of the paper. Does the leading edge of the paper reach the sensor (2500-sheet tray feed)? Go to step 13. Go to step 8. Step 8 Check the 2500.sheet tray feed, pick, and separator rollers for wear or damage, and replace if necessary. See g2500-sheet tray paper feed assembly removalh and g2500-sheet tray pick assembly removalh. Note: If the page count is over 50K, then clean the rollers. Does the problem remain? Go to step 9. The problem is solved. Step 9 a Make sure that the motor (2500-sheet tray feed) is properly installed. b Enter the Diagnostics menu, and then navigate to: MOTOR TESTS > 2500-Sheet Tray Motor Tests > Tray feed Does the motor run? Go to step 17. Go to step 10. Step 10 a Reseat the 2500-sheet tray feed and transport motor cable. b Check the cable for damage, and replace if necessary. Does the problem remain? Go to step 11. The problem is solved. Step 11 a Check the 2500-sheet tray feed and transport motor belt for proper tension, and adjust if necessary. b Check the 2500-sheet tray feed and transport motor belt and gears for wear or damage, and replace if necessary. Does the problem remain? Go to step 12. The problem is solved. Step 12 Replace the motor (2500-sheet tray feed). See gMotor (2500.sheet tray feed) removalh. Does the problem remain? Go to step 13. The problem is solved. Step 13 Check the sensor (2500-sheet tray transport) for damage. Is it free of damage? Go to step 14. Go to step 16. Step 14 Enter the Diagnostics menu, and then navigate to: SENSOR TESTS > 2500-Sheet Tray Sensor Tests Does the sensor status change while toggling the sensor? Go to step 17. Go to step 15. Step 15 a Reseat the 2500-sheet tray transport sensor cable. b Check the cable for damage, and replace if necessary. Does the problem remain? Go to step 16. The problem is solved. Step 16 Replace the sensor (2500-sheet tray transport). See gSensor (2500.sheet tray transport) removalh. Does the problem remain? Go to step 17. The problem is solved. Step 17 Check the 2500-sheet tray controller board pins for damage, and replace if necessary. See g2500-sheet tray controller board removalh. Does the problem remain? Contact the next level of support. The problem is solved.