Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 993 — Lexmark Optra C710

Code: 993

Description: Cam Sensor does not turn on The cam sensor did not activate.
Remedy: Error Code 993: Indicates the cam sensor has not been activated. The sensor activates when the fuser drive motor turns the cam disk. If the fuser drive motor does not turn on, or the drive parts are not operating, go to A. If the fuser drive motor turns and appears to be operating properly, and the cam is turning, go to B. If the fuser drive motor turns and appears to be operating properly, and the cam is not turning, go to C.
A The fuser drive system is not operating properly. 1 Fuser Assembly Fuser Drive Motor Fuser Motor/Paper Feed Motor Carriage Unit Motor Cable Engine Board Check the fuser assembly internal drive gears for binding, or broken or worn teeth. If a problem exists, repair or replace the fuser assembly. Remove the fuser drive motor from the stay assembly, leaving the motor cable connected to the motor. Turn the printer on, but do not allow the motor to touch other areas of the printer. Verify the motor turns during POR. If it does, the problem is most likely in the motor mounting stay assembly. Go to step 2. Check the motor for shorts between the case and each motor winding. If a short is found, replace the motor. Note: Damage to the engine board may result from a shorted motor. Check the motor for open windings. If found, replace the motor. Check continuity of the fuser motor/paper feed motor/carriage unit motor cable. • If incorrect, replace the cable. • If correct, replace the engine board. 2 Motor Mounting Stay Assembly (Fuser Drive Parts) Check the fuser drive gears, gears C3-1, C3- 2, the clutch spring, motor drive gear, gear C2 and C4 for signs of chipped gear teeth, worn parts, or improper operation. If problems are found, repair as necessary. Check the cam gears and solenoid for proper operation and signs of broken or worn gear teeth or damaged parts. If found, repair or replace the motor mounting stay assembly.
B The fuser drive system is operating properly and the cam disk is turning. 1 Cam Sensor (PH16) Engine Board (M4) SN Cable Be sure the cam sensor is mounted correctly and locked into place. Check the following voltages on the cam sensor: Pin # Signal Voltage Voltage Voltage Disc in Disc Out 1 (Orange) +5 V dc +5 V dc +5 V dc 2 (Brown) -CCSENS +5 V dc 0 V dc 3 (Green) GND 0 V dc 0 V dc Note: The voltage on pin 2 should vary, as the cam turns from approximately 0 V to +5 V dc. • If the voltage on Pin 1 is incorrect, check the cable. If incorrect, replace the cable. • If the cable is good, replace the following FRU's in the order shown: 1. Cam sensor 2. Engine board 3. SN cable
C The fuser drive system is operating properly and the cam disk is not turning. 1 Contact Cam Solenoid CRF Cable Engine Board Check the solenoid for proper operation, making sure it picks during POR cycle. Disconnect the solenoid and check the resistance on the solenoid cable. It should measure approximately 65 ohms. If incorrect, replace the solenoid. Check the voltages on the solenoid cable connector. Check the following voltages on the contact cam solenoid cable connector: Pin # Signal Voltage Voltage Voltage Static Picked 1 (Red) +24 V dc +24 V dc +24 V dc 2 (Black) -SL2ON +24 V dc 0 V - +24 V dc Note: All voltages are approximate. If the voltage on Pin 1 is incorrect, check continuity of the CRF cable to the cam solenoid. • If incorrect, replace the cable. • If correct, replace the engine board. 2 Motor Mounting Stay Assembly Check the clutch spring, clutch boss, clutch disk and gear C4 for signs of wear, broken teeth or binds. Repair or replace the motor mounting stay assembly if a problem is found.

← Xem tất cả mã lỗi Lexmark Optra C710

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie