Code: EA10
Description: Finisher jam (Finisher section) Paper Jam in Finisher - Please Clear Paper Path. [MJ-1042] 1st transport motor (M8) fault / 2nd transport motor (M4) fault [MJ-1110] Paper transport delay non-inserting jam
Causes: Parts to be replaced Remark Feeding sensor (S22) Transport path switching solenoid (SOL5) Entrance motor (M1) Finisher control PC board (FIN)
Remedy: MJ-1042
1st transport motor (M8) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connector. (Finisher control PC board (FIN): CN22) 2nd transport motor (M4) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connector. (Finisher control PC board (FIN): CN14) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the motor and the connector, exchange the finisher control PC board (FIN).
MJ-1110
Paper Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Feeding sensor (S22) Check if there is a disconnection of the connector, incorrect installation or breakage of the feeding sensor (S22). If there is, reinstall the sensor correctly or replace it. Transport path switching solenoid (SOL5) Check that the gap between the transfer guide surface and the upper surface of the flapper tip is in the acceptable range according to the status of the transport path switching solenoid (SOL5) (solenoid OFF: 1.5 to 2.1 mm, solenoid ON: 2.3 to 2.9 mm). If it is not, adjust it. Check the harness between the transport path switching solenoid (SOL5) and the finisher controller board (CN1). If there is any abnormality, correct it. Entrance motor (M1) Check the harness between the entrance motor (M1) and the finisher controller board (CN17). If there is any abnormality, correct it. Finisher control PC board (FIN) • Board check • Connector check (CN1, CN17) • Harness check
1st transport motor (M8) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connector. (Finisher control PC board (FIN): CN22) 2nd transport motor (M4) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connector. (Finisher control PC board (FIN): CN14) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the motor and the connector, exchange the finisher control PC board (FIN).
MJ-1110
Paper Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Feeding sensor (S22) Check if there is a disconnection of the connector, incorrect installation or breakage of the feeding sensor (S22). If there is, reinstall the sensor correctly or replace it. Transport path switching solenoid (SOL5) Check that the gap between the transfer guide surface and the upper surface of the flapper tip is in the acceptable range according to the status of the transport path switching solenoid (SOL5) (solenoid OFF: 1.5 to 2.1 mm, solenoid ON: 2.3 to 2.9 mm). If it is not, adjust it. Check the harness between the transport path switching solenoid (SOL5) and the finisher controller board (CN1). If there is any abnormality, correct it. Entrance motor (M1) Check the harness between the entrance motor (M1) and the finisher controller board (CN17). If there is any abnormality, correct it. Finisher control PC board (FIN) • Board check • Connector check (CN1, CN17) • Harness check