Code: EA10
Description: 1st transport motor (M8) fault/ 2nd transport motor (M4) fault [MJ-1036] Paper transport delay jam: The paper which has passed the bridge unit does not reach the entrance sensor.[MJ-1107] The paper which has passed the bridge unit does not reach the entrance sensor. [MJ-1108]
Causes: Entrance sensor Finisher controller PC board
MJ-1108 Feeding sensor (S22) Transport path switching solenoid (SOL5) Entrance motor (M1) Interface PC board (I/F) Finisher control PC board (FIN)
MJ-1108 Feeding sensor (S22) Transport path switching solenoid (SOL5) Entrance motor (M1) Interface PC board (I/F) Finisher control PC board (FIN)
Remedy: MJ-1036 1st transport motor (M8) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connector. (Finisher control PC board (FIN): CN22) 2nd transport motor (M4) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connector. (Finisher control PC board (FIN): CN14) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the motor and the connector, exchange the finisher control PC board (FIN).
MJ-1107 Entrance sensor Is there a disconnection of the connector, incorrect installation or breakage of the entrance sensor (S1)? Gate solenoid • Is the gap between the flapper and entrance roller shaft other than 0.60±0.20mm when the gate solenoid (SOL2) is pulled? • Is the harness between the gate solenoid (SOL2) and the finisher control PC board (CN22) disconnected or open circuited? Entrance motor Is the harness between the entrance motor (M1) and the finisher control PC board (CN7) disconnected or open circuited?
MJ-1108 Finisher Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Feeding sensor (S22) Check if there is a disconnection of the connector, incorrect installation or breakage of the feeding sensor (S22). If there is, reinstall the sensor correctly or replace it. Transport path switching solenoid (SOL5) Check that the gap between the transfer guide surface and the upper surface of the flapper tip is in the acceptable range according to the status of the transport path switching solenoid (SOL5) (solenoid OFF: 1.5 to 2.1 mm, solenoid ON: 2.3 to 2.9 mm). If it is not, adjust it. Entrance motor (M1) Check the harness between the entrance motor (M1) and the finisher controller board (CN26). If there is any abnormality, correct it. Interface PC board (I/F) Check the harness between the transport path switching solenoid (SOL5) and the interface PC board (CN6), If there is any abnormality, correct it. • Board check • Connector check (CN5, CN6, CN7) • Harness check Finisher control PC board (FIN) • Board check • Connector check (CN25, CN27) • Harness check
MJ-1107 Entrance sensor Is there a disconnection of the connector, incorrect installation or breakage of the entrance sensor (S1)? Gate solenoid • Is the gap between the flapper and entrance roller shaft other than 0.60±0.20mm when the gate solenoid (SOL2) is pulled? • Is the harness between the gate solenoid (SOL2) and the finisher control PC board (CN22) disconnected or open circuited? Entrance motor Is the harness between the entrance motor (M1) and the finisher control PC board (CN7) disconnected or open circuited?
MJ-1108 Finisher Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Feeding sensor (S22) Check if there is a disconnection of the connector, incorrect installation or breakage of the feeding sensor (S22). If there is, reinstall the sensor correctly or replace it. Transport path switching solenoid (SOL5) Check that the gap between the transfer guide surface and the upper surface of the flapper tip is in the acceptable range according to the status of the transport path switching solenoid (SOL5) (solenoid OFF: 1.5 to 2.1 mm, solenoid ON: 2.3 to 2.9 mm). If it is not, adjust it. Entrance motor (M1) Check the harness between the entrance motor (M1) and the finisher controller board (CN26). If there is any abnormality, correct it. Interface PC board (I/F) Check the harness between the transport path switching solenoid (SOL5) and the interface PC board (CN6), If there is any abnormality, correct it. • Board check • Connector check (CN5, CN6, CN7) • Harness check Finisher control PC board (FIN) • Board check • Connector check (CN25, CN27) • Harness check