Code: EA10
Description: Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. [MJ-1024/1031/1101]
Remedy: MJ-1025 1. Check if there is any paper remaining in the Finisher or on the transport path of the equipment. Remove if there is. 2. Check if the connector pins are disconnected or the harnesses are open circuited between the inlet sensor and the connector on the finisher controller PC board. Correct if there is any abnormality. 3. Check if the inlet sensor is working normally. (Correct if the actuator does not return normally or if it is deformed or removed.) 4. Replace the sensor. 5. Replace the finisher controller PC board.
MJ-1024 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Check if the connector J708 on the finisher controller PC board is disconnected from the inlet sensor (P133) or the harnesses are open circuited. Correct if any. 3. Is the inlet sensor working properly? (Check the movement of the actuator.) 4. Replace the inlet sensor. 5. Replace the finisher controller PC board.
MJ-1031 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Check if the connector J104 on the finisher controller PC board is disconnected from the inlet sensor (SR2) or the harnesses are open circuited. Correct if any. 3. Is the inlet sensor working properly? (Check the movement of the actuator.) 4. Replace the inlet sensor. 5. Replace the finisher controller PC board.
MJ-1101 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Is there a disconnection of the connector, incorrect installation or breakage of the entrance sensor (S1)? 3. Is the gap between the flapper and entrance roller shaft other than 0.60?0.20mm when the gate solenoid (SOL2) is pulled?. 4. Is the harness between the entrance motor (M1) and the finisher control PC board (CN7) disconnected or open circuited? 5. Is the harness between the gate solenoid (SOL2) and the finisher control PC board (CN22) disconnected or open circuited? 6. Replace the finisher controller PC board.
MJ-1024 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Check if the connector J708 on the finisher controller PC board is disconnected from the inlet sensor (P133) or the harnesses are open circuited. Correct if any. 3. Is the inlet sensor working properly? (Check the movement of the actuator.) 4. Replace the inlet sensor. 5. Replace the finisher controller PC board.
MJ-1031 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Check if the connector J104 on the finisher controller PC board is disconnected from the inlet sensor (SR2) or the harnesses are open circuited. Correct if any. 3. Is the inlet sensor working properly? (Check the movement of the actuator.) 4. Replace the inlet sensor. 5. Replace the finisher controller PC board.
MJ-1101 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Is there a disconnection of the connector, incorrect installation or breakage of the entrance sensor (S1)? 3. Is the gap between the flapper and entrance roller shaft other than 0.60?0.20mm when the gate solenoid (SOL2) is pulled?. 4. Is the harness between the entrance motor (M1) and the finisher control PC board (CN7) disconnected or open circuited? 5. Is the harness between the gate solenoid (SOL2) and the finisher control PC board (CN22) disconnected or open circuited? 6. Replace the finisher controller PC board.