Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi EA40 — Toshiba e-Studio 355

Code: EA40

Description: Door open jam: The Finisher is released from the equipment or any of the staple door and top cover is opened during printing. [MJ-1025] Door open jam: Any of the upper cover and front cover of the Finisher or any of the upper door and front door of the Hole Punch Unit is opened during printing. [MJ-1024] Joint open jam: The joint is released during printing or in the standby status. [MJ-1031]
Remedy: MJ-1025 Is the finisher connected with the equipment? Are the upper cover and front door of the finisher closed? l YES 1. Connect the finisher with the equipment. 2. Close the cover and door of the finisher. NO Is any of the connectors CN4 (upper cover sensor and front door sensor) and CN8 (joint switch) on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and each sensor (upper cover sensor or front door sensor) open-circuited? Is the harness connecting the finisher controller PC board and joint switch (MS2) opencircuited? YES Connect the connector securely. Replace the harness. NO Are the joint switch, upper cover sensor and front door sensor working properly? NO 1. Attach the actuator securely if its shaft is out of place. 2. Replace the switch or sensor. YES Replace the finisher controller PC board.
MJ-1024 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Close the upper or front cover of the finisher if any of them is opened. 3. Check if the connectors J707 and J708 on the finisher controller PC board are disconnected from the upper cover opening sensor (P131) and the front cover opening sensor (P132) , or the harnesses are open circuited. Correct if any. 4. Replace the upper/front cover opening sensor. 5. Check if the connector J719 on the finisher controller PC board is disconnected from the front cover switch (MS31) or the harnesses are open circuited. Correct if any. 6. Replace the front cover switch (MS31). 7. Is the connector J601/J602 on the punch controller PC board disconnected? 8. Is the harness connecting the punch controller PC board and upper door switch (MSW61) open circuited? 9. Is the harness connecting the punch controller PC board and front door switch (MSW62) open circuited? 10.Are the upper and front door switches working properly? 11.Reconnect or replace the connector of the upper cover switch or the front cover switch. 12.Replace the finisher controller PC board.
MJ-1031 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Check if the connector J110 on the finisher controller PC board is disconnected from the Joint switch (SW1) or the harnesses are open circuited. Correct if any. 3. Replace the Joint switch. 4. Replace the finisher controller PC board.
MJ-1101 1. Close the front cover or the stationary tray cover if they are opened. 2. Replace the handle cover installed inside of the front cover if it is broken. 3. Reinstall the stationary tray opening/closing switch if it is incorrectly installed. 4. Check if the connector CN16 on the finisher controller PC board is disconnected from the front cover switch (SW1) and the stationary tray opening/closing switch (SW2) or the harnesses are open circuited. Correct if any. 5. Replace the sensors. 6. Replace the finisher controller PC board.

← Xem tất cả mã lỗi Toshiba e-Studio 355

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie