Code: EA50
Description: Stapling jam: Stapling is not performed properly.
Remedy: MJ-1025 Is there any paper remaining on the stapling tray? YES Remove the paper. NO Open the front door. Is the stapler home position mark blue? YES Rotate the stapler opening dial until the home position mark turns blue. NO Is any of the connectors CN11 (slide home position sensor), CN8 (stapler safety switch) and CN6 (staple/fold motor) on the finisher controller PC board disconnected? Is the stapler unit installed securely? Is the harness connecting the finisher controller PC board and slide home position sensor open-circuited? Is the harness connecting the finisher controller PC board and stapler safety switch opencircuited? YES Connect the connector securely. Replace the harness. NO Are the slide home position sensor and stapler safety switch working properly? l NO 1. Replace the stapler unit. 2. Replace the stapler safety switch. YES Replace the finisher controller PC board.
MJ-1024 1. Check if there is any paper in the finisher or on the transport path of the equipment or on the stapling tray. Remove it if there is. 2. Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? 3. Is the connector J717 on the finisher controller PC board disconnected? 4. Is the harness connecting the finisher controller PC board and staple home position sensor (PI50) open circuited? 5. Is the staple home position sensor working properly? 6. Reconnect or replace the connector of the staple home position sensor. 7. Replace the finisher controller PC board.
MJ-1031 1. Check if there is any paper in the finisher or stapler and remove it if there is. 2. Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? 3. Check if the connectors J112, J113 on the finisher controller PC board is disconnected from the stapler) or the harnesses are open circuited. Correct if any. 4. Check if the connectors on the stapler is disconnected or the harnesses are open circuited. Correct if any. 5. Replace the stapler. 6. Replace the finisher controller PC board.
MJ-1101 1. Check if there is any paper in the finisher or on the transport path of the equipment or on the finishing tray. Remove it if there is. 2. Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? 3. Check if the actuator of the stapler interference sensor (S11) moves smoothly. 4. Check if the connector CN2 on the finisher controller PC board is disconnected from the stapler or the harnesses are open circuited. Correct if any. 5. Check the harnesses in the stapler are disconnected or open circuited. Correct if any. 6. Replace the finisher controller PC board.
MJ-1024 1. Check if there is any paper in the finisher or on the transport path of the equipment or on the stapling tray. Remove it if there is. 2. Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? 3. Is the connector J717 on the finisher controller PC board disconnected? 4. Is the harness connecting the finisher controller PC board and staple home position sensor (PI50) open circuited? 5. Is the staple home position sensor working properly? 6. Reconnect or replace the connector of the staple home position sensor. 7. Replace the finisher controller PC board.
MJ-1031 1. Check if there is any paper in the finisher or stapler and remove it if there is. 2. Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? 3. Check if the connectors J112, J113 on the finisher controller PC board is disconnected from the stapler) or the harnesses are open circuited. Correct if any. 4. Check if the connectors on the stapler is disconnected or the harnesses are open circuited. Correct if any. 5. Replace the stapler. 6. Replace the finisher controller PC board.
MJ-1101 1. Check if there is any paper in the finisher or on the transport path of the equipment or on the finishing tray. Remove it if there is. 2. Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? 3. Check if the actuator of the stapler interference sensor (S11) moves smoothly. 4. Check if the connector CN2 on the finisher controller PC board is disconnected from the stapler or the harnesses are open circuited. Correct if any. 5. Check the harnesses in the stapler are disconnected or open circuited. Correct if any. 6. Replace the finisher controller PC board.