Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi CB51 — Toshiba e-Studio 456

Code: CB51

Description: Stapler shift home position error: The stapler is not at the home position. [MJ-1101/MJ-1106] Stapler unit sliding home position detection error: The detection of the home position of the stapler unit sliding ends abnormally. [MJ-1032/MJ-1033]
Causes: MJ-1101 Stapler unit home position sensor (S10) Finisher controller PC board
MJ-1106 Stapler unit home position sensor Finisher controller PC board
Remedy: MJ-1101 Stapler If there is mechanical problem when the stapler is moved, fix the mechanism. Stapler unit home position sensor (S10) • Sensor check • Check the connectors and harnesses between the stapler unit home position sensor (S10) and the finisher control PC board (CN1). Stapler unit shift motor (M4) Check the connectors and harnesses between the stapler unit shift motor (M4) and the finisher control PC board (CN5).
MJ-1106 Stapler Move the stapler. Fix any mechanical problem. Stapler unit home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the stapler unit home position sensor (S10). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN21) on the finisher controller PC board is disconnected from the stapler unit home position sensor (S10) and the harnesses are open circuited. Correct if so. Stapler unit shift motor Check if the connector (CN10) on the finisher controller PC board is disconnected from the stapler unit shift motor (M9) and the harnesses are open circuited. Correct if so.
MJ-1032 Staple unit sliding motor (M7) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the staple unit. Staple unit sliding home position sensor (S3) abnormality Measure the voltage on TP18 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V±5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connectors. (Finisher control PC board (FIN): CN3, CN18) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the staple unit, sensors and connectors, exchange the finisher control PC board (FIN).
MJ-1033 Staple unit sliding motor (M11) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the staple unit. Edge staple unit sliding home position sensor (S14) abnormality Measure the voltage on pin CN7.6 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V ± 5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Saddle stitch staple unit sliding home position sensor (S22) abnormality Measure the voltage on pin CN7.10 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V ± 5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Edge staple unit improper clinching prevention sensor (S25) abnormality Measure the voltage on pin CN10.11 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V ± 5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connectors. (Finisher control PC board (FIN): CN7, CN10, CN17) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the staple unit, sensors and connectors, exchange the finisher control PC board (FIN).

← Xem tất cả mã lỗi Toshiba e-Studio 456

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie