Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi E8-2 — Xerox Phaser 5400

Code: E8-2

Description: Jam at E - E8-2 Duplex Area Jam Paper being fed into the Duplex Unit did not reach the Wait Sensor on time.
Causes: • Duplex Wait Sensor • Exit 2 Motor • Exit 2 OCT Roller • Exit 2 FU Roller • Exit 2 Inv Roller • Exit PWB • Duplex Unit PWB • Engine Control Board • LVPS
Remedy: 1 Check paper position at Door E. Does paper remain in Exit 2? Remove the paper. Go to Step 2. 2 Check the FU Roller. Is the FU Roller worn or contaminated with paper dust? Clean or replace the FU Roller. Go to Step 3. 3 Check the drive transmission. Does the FU Roller and gears rotate smoothly? Go to Step 4. Restore proper operation. 4 Check the Inv Roller. Is the INV Roller worn or contaminated with paper dust? Clean or replace the INV Roller. Go to Step 5. 5 Check the drive transmission. Does the INV Roller and gears rotate smoothly? Go to Step 6. Restore proper operation. 6 Check the OCT Roller. Is the OCT Roller worn or contaminated with paper dust? Clean or replace the OCT Roller. Go to Step 7. 7 Check the drive transmission. Does the OCT Roller and gears rotate smoothly? Go to Step 8. Restore proper operation. 8 Test the Exit 2 Motor. Run the Service Diagnostics Exit 2 Motor tests. Does the Exit 2 Motor operate properly? Go to Step 17. Go to Step 9. 9 Check the Exit 2 Motor connections. Are P/J208, P/J606A and P/J433 connected? Go to Step 10. Connect P/J208, P/J606A and P/ J433. 10 Check continuity between the Exit Motor and Exit PWB. Is there continuity on each wire between P/ J208 <=> P/J433? Go to Step 11. Repair the wiring. 11 Check for +24 V to the Exit 2 Motor. Is there +24 V across P208-5 (+) <=> ground? Replace the Exit 2 Motor. Go to Step 12. 12 Check the connection between the Exit PWB and Engine Control Board. Are P/J431 and P/J421 connected? Go to Step 13. Connect P/J431 and P/J421. 13 Check continuity between the Exit PWB and the Engine Control Board. Is there continuity on each wire between P/ J431 <=> P/J421? Go to Step 14. Repair the wiring. 14 Check the connection between the Exit PWB and the LVPS. Are P/J430 and P/J526 connected? Go to Step 15. Connect P/J430 and P/J526. 15 Check continuity between the Exit PWB and the LVPS. Is there continuity on each wire between P/ J430 <=> P/J526? Go to Step 16. Repair the wiring. 16 Check for +24 V to the Exit PWB. Is there +24 V across P/J430-1 (+) <=> ground? Replace the Exit PWB. Replace the LVPS. 17 Test the Wait Sensor. Run the Service Diagnostics Duplex Wait Sensor test. Does the Wait Sensor operate properly? Replace the Engine Control Board. Go to Step 18. 18 Check the Wait Sensor connection. Are P/J123 and P/J541 connected? Go to Step 19. Connect P/J123 and P/J541. 19 Check continuity between the Wait Sensor and Duplex PWB. Is there continuity on each wire between P/ J123 <=> P/J541? Go to Step 20. Repair the wiring. 20 Check for +5 V to the Wait Sensor. Is there +5 V across P123-3 (+) <=> ground? Replace the Wait Sensor. Go to Step 21. 21 Check the Duplex PWB connection. Are P/J540 and P/J417 connected? Go to Step 22. Connect P/J540 and P/J417 surely. 22 Check continuity between the Duplex PWB and Engine Control Board. Is there continuity on each wire between P/ J540 <=> P/J417? Go to Step 23. Repair the wiring. 23 Check for +5 V to the Duplex PWB. Is there +5 V across P/J540-1 (+) <=> ground? Replace the Duplex PWB. Replace the Engine Control Board.

← Xem tất cả mã lỗi Xerox Phaser 5400

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie