Code: H1-1 ... H1-4
Description: Tray n Failure - H1 -1/2/3/4 Tray n Fail Detected lift failure. Paper size detection inoperative. • Tray 2 Failure - H1-1 Tray 2 Fail • Tray 3 Failure - H1-2 Tray 3 Fail • Tray 4 Failure - H1-3 Tray 4 Fail • Tray 5 Failure - H1-4 Tray 5 Fail
Causes: • Tray • Feeder • Feed/Lift Motor • Level Sensor • Paper Size Switch • Tray 4-5 PWB • Engine Control Board
Remedy: 1 Check paper supply. Is paper loaded in the affected tray? Go to Step 2. Load paper and go to Step 2. 2 Check the tray. Replace the tray with one from another position. Does the replaced tray lift? Go to Step 3. Go to Step 4. 3 Check lift components. Is the Sector Gear or surrounding parts damaged? Replace the tray. Go to Step 4. 4 Test the Feed/Lift Motor. Run the Service Diagnostics Lift Motor test for the affected tray. Does the motor operate properly? Go to Step 9. Go to Step 5. 5 Check the Feed/Lift Motor connections. Is the affected Feed/Lift motor properly connected to the harness? Go to Step 6. Connect the motor. If error continues, go to Step 6. 6 Test the Feed/Lift Motor. 1. Exchange the Feed/Lift Motor with one from an operational feeder. 2. Run the Service Diagnostics Lift Motor test on the replacement motor. Does the motor operate properly? Replace the Feed/ Lift motor. Go to Step 7. 7 Check for continuity on the connections. Reinstall the motors in the original feeders. Is there continuity on each wire between P/ J409 (Trays 2-3) or P/J549 (Trays 4-5) and the Feeder Harness? Go to Step 8. Repair the wiring. 8 Check for +24 V to the affected Feed/Lift Motor. Is there +24 V across the motor connector’s Pin 4(+) <=> ground? Replace the motor. Replace the Engine Control Board. If the error persists, replace the Tray 4-5 PWB. 9 Test the affected Level Sensor. Run the Service Diagnostics Level Sensor test for the affected tray. Does the sensor state change? Go to Step 13. Go to Step 10. 10 Check the Level Sensor connection. Is the sensor connected to the harness? Go to Step 11. Connect the sensor. If error persists, go to Step 11. 11 Check harness continuity between the Level Sensor and Engine Control Board. Is there continuity on each wire between the Level Sensor <=> P/J409 (Trays 2-3) or P/ J549 (Trays 4-5)? Go to Step 12. Repair the wiring. 12 Check for +5 V to the affected Level Sensor. Is there +5 V across Pin-3 (+) <=> ground? Replace the sensor. Replace the Engine Control Board. If the error persists, replace the Tray 4-5 PWB. 13 Test the affected Paper Size Switch. Run the Service Diagnostics Paper Size Sensor test for the affected tray. Is the paper size detected correctly when the tray, loaded with paper, is moved in and out? Replace the Engine Control Board. If the error persists replace Tray 4-5 PWB. Go to Step 14. 14 Check the affected Paper Size Switch connection. Is the switch connected to the harness? Go to Step 15. Connect the switch. If problem persists, go to Step 15. 15 Check continuity between the Paper Size Switch and the Engine Control Board (Tray 2-3) or Tray 4-5 PWB (Tray 4-5). Is there continuity on each wire between the switch <=> P/J412 (Tray 2-3) or P/J548 (Tray 4-5)? Go to Step 16. Repair the wiring. 16 Check for +3.3 V to the Paper Size Switch. Is there +5 V across P/J412-1 (+) <=> ground? for Tray 2-3 or 3.3 V across P/J548- 1 for Tray 4-5. Replace the switch. Replace the Engine Control Board. If the error persists, replace the Tray 4-5 PWB.