Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H1-5 — Xerox Phaser 5400

Code: H1-5

Description: Tray 6 Failure - H1-5 Tray 6 Fail Detected lift failure or paper size detection inoperative.
Causes: • Tray In Sensor • Tray 6 Main Harness • Tray 6 Feeder Harness • Tray 6 PWB • Lift Cables • Feed/Lift Motor • Nudger Solenoid • Level Sensor • Engine Control Board
Remedy: 1 Check Tray In Sensor alignment. Pull the Tray out. Does the actuator enter the sensing area of the Tray Set Sensor, or is it deformed or damaged? Go to Step 2. Repair the damage and go to Step 2. 2 Check the Tray installation. Is the Tray installed correctly? Go to Step 3. Correct and go to Step 3. 3 Check the repairs. Does the error reoccur? Go to Step 4. Problem solved. 4 Test the Tray In Sensor. Run the Service Diagnostics Tray In Sensor test. Does the sensor status change when the tray is moved in and out? Go to Step 10. Go to Step 5. 5 Check the Tray In Sensor Main Harness connection. Are PF53 and JF01 connected? Go to Step 7. Connect and go to Step 6. 6 Check the repairs. Does the error reoccur? Go to Step 7. Problem solved. 7 Check Tray In Sensor Main Harness continuity. 1. Disconnect PF53 and JF01. 2. Check for continuity at the following: • PF53-1 <=> JF01-6 • PF53-2 <=> JF01-5 • PF53-3 <=> JF01-4 Are these conductive? Go to Step 8. Repair the Tray 6 Tray Set Sensor harness. 8 Check for +5 V to the Tray In Sensor. Is there +5 V across PF01-6 <=> PF04-2 on the Tray 6 PWB? Go to Step 9. Replace the Tray 6 PWB. 9 Check Tray In Sensor signal. Does the voltage across JF01-5 <=> PF04-2 on the Tray 6 PWB change when the sensor is blocked? Go to Step 36. Replace the sensor. 10 Check the Tray cables. Remove the Tray from the HCF. Are the two cables installed correctly? Go to Step 11. Correct and go to Step 11. 11 Test the Level Sensor. Run the Service Diagnostics Tray 6 Level Sensor test. Does the sensor state change? Go to Step 19. Go to Step 12. 12 Check the Level Sensor Harness connections. Are PF62 and PF56B connected? Go to Step 13. Connect and go to Step 13. 13 Check the Level Sensor Harness connections. Are PF56B and JF02 connected? Go to Step 15. Connect and go to Step 14. 14 Check the repair. Does the error still occur? Go to Step 15. Problem solved. 15 Check Level Sensor Harness continuity. 1. Disconnect PF62 and JF56B. 2. Check for continuity at the following: • PF62-1 <=> JF56B-6 • PF62-2 <=> JF56B-5 • PF62-3 <=> JF56B-4 Are these conductive? Go to Step 16. Repair the Tray 6 Feeder Harness.

← Xem tất cả mã lỗi Xerox Phaser 5400

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie