Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H5-21, H5-23 — Xerox Phaser 5400

Code: H5-21, H5-23

Description: Stacker Lower Tray Failure - H5-2n Front Home Sensor For H5-21, the Front Tamper Home Sensor is not turned On within 800 ms following the Front Tamper beginning to move to the Front Tamper Home position. For H5-23, the Front Tamper Home Sensor is not turned Off in the time specified following the Front Tamper leaving the home position, or the Front Tamper Home Sensor is turned On again after the Front Tamper Home Sensor is turned Off and the Front Tamper stops moving. • Stacker Lower Tray Failure - H5-21 Front Home SNR ON • Stacker Lower Tray Failure - H5-23 Front Home SNR OFF
Causes: • Front Tamper Home Sensor • Compiler Tray Assembly • Compiler Harness • Finisher Main PWB • Front Tamper Motor
Remedy: 1 Check the Tamper mechanism. Move the Front Tamper mechanism. Does the Tamper mechanism operate smoothly? Go to Step 2. Repair or replace the Compiler Tray. 2 Test the Front Tamper Home Sensor. Run the Service Diagnostics Front Tamper Home Sensor test. Does the sensor state change when the sensor is blocked? Go to Step 8. Go to Step 3. 3 Check the Compiler harness connections. Are P/J8360 and P/J8309 connected? Go to Step 5. Connect and go to Step 4. 4 Print a Test Print. Does the error still occur? Go to Step 5. Problem solved. 5 Check Compiler Front Tamper Harness continuity. 1. Disconnect P/J8360 on the harness and P/J8309 on the Finisher Main PWB. 2. Check for continuity at the following: • P/J8360-3 <=> P/J8309-4 • P/J8360-2 <=> P/J8309-5 • P/J8360-1 <=> P/J8309-6 Are these conductive? Go to Step 6. Repair the Compiler Front Tamper Harness. 6 Check for +5 V to the Front Tamper Home Sensor. Is there +5 V across J8309-6 <=> J8309-4 on the Finisher Main PWB? Go to Step 7. Replace the Finisher Main PWB. 7 Check Front Tamper Home Sensor signal. Does the voltage across P8309-5 <=> P8309-4 on the Finisher Main PWB change when the sensor is blocked? Replace the Finisher Main PWB. Replace the Front Tamper Home Sensor. 8 Test the Front Tamper Motor. Run the Service Diagnostics Front Tamper Motor Low Speed Inboard and Outboard tests alternately. Does the Front Tamper Motor rotate, and the Tamper move front to rear? Replace the Finisher Main PWB. Go to Step 9. 9 Check Compiler Front Tamper Motor Harness connections. Are P/J8363B and P/J8309 connected? Go to Step 11. Connect and go to Step 10. 10 Print a Test Print. Does the error still occur? Go to Step 11. Problem solved. 11 Check Compiler Front Tamper Motor Harness continuity. 1. Disconnect P/J8363B and P/J8309. 2. Check for continuity at the following: • P/J8363B-6 <=> P/J8309-10 • P/J8363B-5 <=> P/J8309-11 • P/J8363B-4 <=> P/J8309-12 • P/J8363B-3 <=> P/J8309-13 • P/J8363B-2 <=> No connection • P/J8363B-1 <=> P/J8309-14 Are these conductive? Go to Step 12. Repair the Compiler Front Tamper Motor Harness. 12 Check for +24 V to the Front Tamper Motor. Is there +24 V across J8309-11 <=> ground on the Finisher Main PWB? Go to Step 13. Replace the Finisher Main PWB. 13 Replace the Front Tamper Motor. Print a Test Print. Does the error still occur? Replace the Finisher Main PWB. Problem solved.

← Xem tất cả mã lỗi Xerox Phaser 5400

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie