Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H5-31, H5-32 — Xerox Phaser 5400

Code: H5-31, H5-32

Description: Punch Failure - H5-3n Sensor The Punch Home Sensor is not turned On (H5-31) or Off (H5-32) within the specified time after Punch Motor activation. • Punch Failure - H5-31 SNR ON • Punch Failure - H5-32 SNR OFF
Causes: • Punch Home Sensor • Punch Harness • Punch Sensor Harness • Finisher Main PWB • Punch Motor • Punch Drive Harness
Remedy: 1 Check the Punch operation. Does the punch move smoothly? Go to Step 2. Correct the installation. 2 Test the Punch Home Sensor. Run the Service Diagnostics Punch Home Sensor test. Does the sensor change state when the sensor is blocked? Go to Step 9. Go to Step 3. 3 Check Punch Home Sensor harness connections. Are P/J8348 and P/J8333 on the Punch Harness, and P/J8333 and P/J8307 on the Punch Sensor Harness connected? Go to Step 5. Connect and go to Step 4. 4 Print a Test Print. Does the error still occur? Go to Step 5. Problem solved. 5 Check Punch Home Sensor Harness continuity. 1. Disconnect P/J8348 and P/J8333. 2. Check for continuity at the following: • P/J8348-3 <=> P/J8333-7 • P/J8348-2 <=> P/J8333-8 • P/J8348-1 <=> P/J8333-9 Are these conductive? Go to Step 6. Repair the Punch Home Sensor Harness. 6 Check Punch Home Sensor Harness continuity. 1. Disconnect P/J8333 and P/J8307. 2. Check for continuity at the following: • P/J8333-7 <=> P/J8307-B6 • P/J8333-8 <=> P/J8307-B5 • P/J8333-9 <=> P/J8307-B4 Are these conductive? Go to Step 7. Repair the Punch Home Sensor Harness. 7 Check for +5 V to the Punch Home Sensor. Is there +5 V across J8307-B6 <=> J8307- B5 on the Finisher Main PWB? Go to Step 8. Replace the Finisher Main PWB. 8 Check the Punch Home Sensor signal. Does the voltage across P8307-B4 <=> P8307-B5 on the Finisher Main PWB change when the sensor is blocked? Replace the Finisher Main PWB. Replace the Punch Home Sensor. 9 Test the Punch Motor. Run the Service Diagnostics Punch Unit Motor Front and Rear tests. Does the Punch Motor rotate? Replace the Finisher Main PWB. Go to Step 10. 10 Check the harness connections. Are P/J8345 and P/J8332 on the Punch Harness, and P/J8332 and P/J8306 on the Punch Drive Harness connected? Go to Step 12. Connect and go to Step 11. 11 Print a Test Print. Does the error still occur? Go to Step 12. Problem solved. 12 Check Punch Motor Harness continuity. 1. Disconnect P/J8345 and P/J8332. 2. Check for continuity at the following: • P/J8345-2 <=> P/J8332-2 • P/J8345-1 <=> P/J8332-1 Are these conductive? Go to Step 13. Repair the Punch Harness. 13 Check Punch Motor Drive Harness continuity. 1. Disconnect P/J8332 and P/J8306. 2. Check for continuity at the following: • P/J8332-2 <=> P/J8306-8 • P/J8332-1 <=> P/J8306-7 Are these conductive? Go to Step 14. Repair the Punch Motor Drive Harness. 14 Replace the Punch Motor. Print a Test Print. Does the error still occur? Replace the Finisher Main PWB. Problem solved.

← Xem tất cả mã lỗi Xerox Phaser 5400

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie