Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi U4-1 — Xerox Phaser 5400

Code: U4-1

Description: Fuser Failure - U4-1 On Time NOTE: Following display of this error, leave power applied for 7 minutes, then cycle printer power. If the error reoccurs, proceed with troubleshooting procedure. The Fuser failed to reach temperature within the warm-up period. Possible faults are: • During the Warm-Up period, the Control Thermistor does not detect the Ready temperature even when the specified time has passed. • During the Standby period, the Control Thermistor does not detect the required temperature even when the specified time has passed. • During idling after power-on, the Control Thermistor does not detect the idling stop temperature even after the specified time has passed. • During print, the Control Thermistor does not detect the required temperature even when the specified time has passed.
Causes: • Fuser • LVPS
Remedy: 1 Check the Fuser for a paper jam. Open Door A. Is there a paper jam in the Fuser? Remove the paper. Go to Step 2. 2 Check the Fuser installation. Is the Fuser installed properly? Go to Step 3. Correct the installation. If the error persists, replace the Fuser and go to Step 10. 3 Check continuity on the junction connector. WARNING Allow the Fuser to cool. Remove the Fuser. Is there continuity on the pins? Go to Step 4. Replace the Fuser. 4 Check Fuser resistance. Is the resistance across P/J600-1 and P/ J600-11 less than or equal to 100 ohms? Go to Step 5. Replace the Fuser. 5 Check Fuser resistance. Is the resistance across P/J600-4 and P/ J600-11 less than or equal to 100 ohm? Go to Step 6. Replace the Fuser. 6 Check Fuser resistance. Is the resistance across P/J600-7 and P/ J600-11 less than or equal to 100 ohm? Go to Step 7. Replace the Fuser. 7 Check Fuser resistance. Is the resistance across P/J131-1 and P/ J131-2 more than or equal to 3 k-ohm? Go to Step 8. Replace the Fuser. 8 Check Fuser resistance. Is the resistance between P/J132-1 and P/ J132-2 greater than or equal to 3 k-ohm? Go to Step 9. Replace the Fuser. 9 Check Fuser resistance. Is the resistance across P/J133-1 and P/ J133-2 greater than or equal to 3 k-ohm? Go to Step 10. Replace the Fuser. 10 Check Fuser connection. Is P/J6 connected? Go to Step 11. Connect P/J6. 11 Check continuity between the Fuser and LVPS. Is there continuity on each wire between P/ J600 <=> P/J6? Go to Step 12. Repair the wiring. 12 Check for +5 V to the Fuser. Is there +5 V between these pins? • P/J6-1 <=> P6-2 • P/J6-1 <=> P6-3 • P/J6-1 <=> P6-4 Replace the Fuser. Replace the LVPS. 13 Check the LVPS and the Engine Control Board connection. Are P/J401 and P/J525 connected? Replace the Engine Control Board. Connect P/J401 and P/J525.

← Xem tất cả mã lỗi Xerox Phaser 5400

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie