Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H5-33, H5-34 — Xerox Phaser 5500

Code: H5-33, H5-34

Description: Punch Failure - H5-3n Home Sensor The Punch Unit Move Home Sensor does not change state within the specified time following activation of the Punch Move Motor or the Move Home sensor changes state after the Punch Move Motor has stopped. • Punch Failure - H5-33 Home SNR ON • Punch Failure - H5-34 Home SNR OFF
Causes: • Punch Unit Move Home Sensor • Punch Sensor Harness • Finisher Main PWB • Punch Motor Bracket • Punch Drive Harness
Remedy: 1 Check the Punch Unit operation. Slide the Punch Unit in and out. Does the Punch Unit move smoothly? Go to Step 2. Correct the installation. 2 Test the Punch Unit Move Home Sensor. Run the Service Diagnostics Punch Unit Move Home Sensor test. Does the sensor state when the sensor is blocked? Go to Step 8. Go to Step 3. 3 Check Punch Unit Move Home Sensor Harness connection. Are P/J8352 and P/J8307 connected? Go to Step 5. Connect and go to Step 4. 4 Print a Test Print. Does the error still occur? Go to Step 5. Problem solved. 5 Check Punch Unit Move Home Sensor Harness continuity. 1. Disconnect P/J8352 and P/J8307. 2. Check for continuity at the following: • P/J8352-3 <=> P/J8307-A6 • P/J8352-2 <=> P/J8307-A5 • P/J8352-1 <=> P/J8307-A4 Are these conductive? Go to Step 6. Repair the Punch Unit Move Home Sensor Harness. 6 Check for +5 V to the Punch Unit Move Home Sensor. Is there +5 V across J8307-A4 <=> J8307- A6 on the Finisher Main PWB? Go to Step 7. Replace the Finisher Main PWB. 7 Check the Punch Home Sensor signal. Does the voltage across P8307-A5 <=> P8307-A6 on the Finisher Main PWB change when the sensor is blocked? Replace the Finisher Main PWB. Replace the Punch Unit Move Home Sensor. 8 Test the Punch Move Motor. Run the Service Diagnostics Front and Rear Punch Move Motor tests. Does the Punch Move Motor rotate and the Punch frame move? Replace the Finisher Main PWB. Go to Step 9. 9 Check Punch Motor Harness connections. Are P/J8344 and P/J8306 connected? Go to Step 11. Connect and go to Step 10. 10 Print a Test Print. Does the error still occur? Go to Step 11. Problem solved. 11 Check Punch Motor Harness continuity. 1. Disconnect P/J8344 and P/J8306. 2. Check for continuity at the following: • P/J8344-1 <=> P/J8306-7 • P/J8344-2 <=> P/J8306-3 • P/J8344-3 <=> P/J8306-6 • P/J8344-4 <=> P/J8306-5 • P/J8344-5 <=> P/J8306-2 • P/J8344-6 <=> P/J8306-1 Are these conductive? Go to Step 12. Repair the Punch Motor Harness. 12 Replace the Punch Move Motor. Print a Test Print. Does the error still occur? Go to Step 13. Problem solved. 13 Replace the Finisher Main PWB. Does the error still occur? Replace the Finisher Main PWB.

← Xem tất cả mã lỗi Xerox Phaser 5500

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie