Code: 077-104
Description: Reg Off Jam The paper does not pass through the Registration Sensor within the specified time.
Causes: • Registration Sensor, PL2.3.5 • Registration Clutch, PL2.3.7 • Harn assy rkn sns, PL2.2.25/26 • Main Drive Assembly, PL6.1.2 • Harn assy main mot, PL6.1.7 • MCU Board, PL7.2.2
Remedy: • Check the media path for obstructions or debris. • Cycle printer power. • If the problem persists, follow this procedure.
1 Check the installation and operation of the Registration Roller and the Registration Pinch Roller Assembly. Are the Registration Roller and the Registration Pinch Roller Assembly installed properly? Go to step 2. Replace the relevant part, then go to step 2. 2 Check connectors P/J12 and P/J120 between the MCU Board and the Registration Sensor. Are the connectors secure? Go to step 3. Reconnect the connectors, then go to step 3. 3 Does the error still occur when printing? Go to step 4. Complete. 4 Enter diagnostic mode and run the Regi Sensor test (see page 4-6). You can also use the CE Diag Tool to run this test (see page A-6). Lift the Main Paper Tray Chute (PL3.3.3), does the number on the display increase by 1 each time the Main Paper Tray Chute is lifted? Replace the MCU Board. Go to step 5. 5 Disconnect the MCU Board P/J21 and the Registration Sensor P/J120. Check the harness assy rkn sns for continuity. Is the harness damaged? Go to step 6. Repair the harness. 6 Check that the voltage across ground on the MCU Board P/J12-1 is +3.3 VDC. Is the voltage correct? Replace the Registration Sensor. Replace the MCU Board. 7 Check connectors P/J16 and P/J160 between the MCU Board and the Main Drive Assembly. Are the connectors secure? Go to step 9. Reconnect the connectors, then go to step 8. 8 Does the error persist when printing? Go to step 9. Complete. 9 Enter diagnostic mode and run the Main Motor test (see page 4-6). You can also use the CE Diag Tool to run this test. (see page A-14). Does the Main Drive Assembly function normally? Go to step 14. Go to step 10. 10 Check the Main Drive Assembly for proper installation. Is the Main Drive Assembly installed correctly? Go to step 12. Reseat the Main Drive Assembly, then go to step 11. 11 Does the error still occur when printing? Go to step 12. Complete. 12 Disconnect P/J16 from the MCU Board and P/J160 from the Main Drive Assembly. Check the continuity of the cable. Is the cable damaged? Repair the cable. Go to step 13. 13 Check the MCU Board P/J25 for proper connection. Is P/J25 securely connected? Go to step 15. Reconnect the connector, then go to step 14. 14 Does the error persist when printing? Go to step 15. Complete. 15 Check the power to the Main Drive Assembly. Disconnect P/J16 on the MCU Board. Are the voltages across ground at P/J16-2 and P/J16-4 approximately +24 VDC when the Interlock Switch is pushed? Replace the Main Drive Assembly, then go to step 16. Replace the MCU Board, then go to step 16. 16 Does the error persist when printing? Go to step 17. 17 Enter diagnostic mode and run the Regi Clutch test. You can also use the CE Diag Tool to run this test (see page A-14). Does the Registration Clutch function correctly? Replace the MCU Board. Replace the Registration Clutch.
1 Check the installation and operation of the Registration Roller and the Registration Pinch Roller Assembly. Are the Registration Roller and the Registration Pinch Roller Assembly installed properly? Go to step 2. Replace the relevant part, then go to step 2. 2 Check connectors P/J12 and P/J120 between the MCU Board and the Registration Sensor. Are the connectors secure? Go to step 3. Reconnect the connectors, then go to step 3. 3 Does the error still occur when printing? Go to step 4. Complete. 4 Enter diagnostic mode and run the Regi Sensor test (see page 4-6). You can also use the CE Diag Tool to run this test (see page A-6). Lift the Main Paper Tray Chute (PL3.3.3), does the number on the display increase by 1 each time the Main Paper Tray Chute is lifted? Replace the MCU Board. Go to step 5. 5 Disconnect the MCU Board P/J21 and the Registration Sensor P/J120. Check the harness assy rkn sns for continuity. Is the harness damaged? Go to step 6. Repair the harness. 6 Check that the voltage across ground on the MCU Board P/J12-1 is +3.3 VDC. Is the voltage correct? Replace the Registration Sensor. Replace the MCU Board. 7 Check connectors P/J16 and P/J160 between the MCU Board and the Main Drive Assembly. Are the connectors secure? Go to step 9. Reconnect the connectors, then go to step 8. 8 Does the error persist when printing? Go to step 9. Complete. 9 Enter diagnostic mode and run the Main Motor test (see page 4-6). You can also use the CE Diag Tool to run this test. (see page A-14). Does the Main Drive Assembly function normally? Go to step 14. Go to step 10. 10 Check the Main Drive Assembly for proper installation. Is the Main Drive Assembly installed correctly? Go to step 12. Reseat the Main Drive Assembly, then go to step 11. 11 Does the error still occur when printing? Go to step 12. Complete. 12 Disconnect P/J16 from the MCU Board and P/J160 from the Main Drive Assembly. Check the continuity of the cable. Is the cable damaged? Repair the cable. Go to step 13. 13 Check the MCU Board P/J25 for proper connection. Is P/J25 securely connected? Go to step 15. Reconnect the connector, then go to step 14. 14 Does the error persist when printing? Go to step 15. Complete. 15 Check the power to the Main Drive Assembly. Disconnect P/J16 on the MCU Board. Are the voltages across ground at P/J16-2 and P/J16-4 approximately +24 VDC when the Interlock Switch is pushed? Replace the Main Drive Assembly, then go to step 16. Replace the MCU Board, then go to step 16. 16 Does the error persist when printing? Go to step 17. 17 Enter diagnostic mode and run the Regi Clutch test. You can also use the CE Diag Tool to run this test (see page A-14). Does the Registration Clutch function correctly? Replace the MCU Board. Replace the Registration Clutch.