Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 024-959 — Xerox Phaser 6180

Code: 024-959

Description: Load Tray 2 (No Suitable Paper) The type or size of paper mismatched or Tray 2 is empty. The following troubleshooting procedure applies to this error.
Causes: • Tray 2, PL2.1.24 • Feeder Unit, PL3.2.1 • Tray 2 No Paper Sensor, PL3.2.30 • Registration Sensor Harness, PL3.2.37 • No Paper Actuator, PL3.2.49 • MCU Board, PL9.2.13 • Right Side Harness, PL10.
Remedy: 1 1. Check the paper size. 2. Does the paper size meet specifications? Go to step 2. Replace the paper with the correct specifications. 2 1. Check the paper size setting. 2. Does the paper match with the settings on the printer Control Panel? Go to step 3. Correct the paper settings on the printer Control Panel. Go to step 3. 3 1. Check the paper type. • Paper in the tray • Paper type setting in the Control Panel • Paper type of the printing job 2. Are these paper types the same? Go to step 4. Correct the paper type setting on the printer Control Panel. 4 1. Reseat Tray 2. 2. Does the error still occur when printing? Go to step 5. Complete. 5 1. Check the No Paper Actuator. 2. Does the Actuator operate smoothly? Go to step 6. Replace the Feeder Unit. 6 1. Perform the Tray 2 No Paper test: Service Mode > Printer Diag > Engine Diag > Sensor Test > Tray 2 No Paper. 2. Does the number on the Control Panel increase by 1 every time the Actuator is activated? Replace the MCU Board. Go to step 7. 7 1. Check the wiring harness connectors P/J23, P/J232, and P/ J2321 between the No Paper Sensor and the MCU Board. 2. Are the connectors securely connected? Go to step 8. Reconnect the connectors. 8 Check the Right Side Harness for continuity. 1. Disconnect P/J23 from the MCU Board. 2. Disconnect P/J232 from the Registration Sensor Harness. 3. Check continuity between P/J23 <=> P/J232. Go to step 9. Replace the Right Side Harness. 9 Check the Registration Sensor Harness for continuity. 1. Disconnect P/J232 from the Right Side Harness. 2. Disconnect P/J2321 from the No Paper Sensor. 3. Check continuity between P/J232 <=> P/J2321. Go to step 10. Replace the Registration Sensor Harness. 10 Check the No Paper Sensor signal. 1. Disconnect P/J23 from the MCU Board. 2. Is there +3.3 V across ground <=> J23-5 pin on the MCU Board? Go to step 11. Replace the MCU Board. 11 Check the No Paper Sensor for operation. 1. Measure the voltage across ground <=> J23-7 on the MCU Board. 2. Does the voltage change when the No Paper Sensor is activated? Replace the MCU Board. Replace the No Paper Sensor.

← Xem tất cả mã lỗi Xerox Phaser 6180

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie