Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 024-960 — Xerox Phaser 6180

Code: 024-960

Description: Load Tray 3 (No Suitable Paper) The type or size of paper mismatched or Tray 3 is empty. The following troubleshooting procedure applies to this error.
Causes: • Feeder Unit, PL3.2.1 • Registration Sensor, PL3.2.30 • Registration Sensor Harness, PL3.2.37 • No Paper Actuator, PL3.2.49 • MCU Board, PL9.2.13 • Right Side Harness, PL10.1.12 • 550-Sheet Feeder, PL13.1.1 • Tray 3 Feeder, PL13.2.8 • Tray 3 Feeder Harness, PL13.3.3 • Tray 3, PL13.4.1
Remedy: 1 1. Check the paper size. 2. Does the paper size meet specifications? Go to step 2. Replace the paper with the correct specifications. 2 1. Check the paper size setting. 2. Does the paper match with the settings in the Control Panel? Go to step 3. Correct the paper settings in the Control Panel. Go to step 3. 3 1. Check the paper type. • Paper in the tray • Paper type setting on the printer Control Panel • Paper type of the printing job 2. Are the paper types the same? Go to step 4. Correct the paper type setting on the printer Control Panel. 4 1. Reseat Tray 3. 2. Does the error still occur when printing? Go to step 5. Complete. 5 1. Check the No Paper Actuator. 2. Does the Actuator operate smoothly? Go to step 6. Replace the Tray 3 Feeder. 6 1. Perform the Tray 3 No Paper test: Service Mode > Printer Diag > Engine Diag > Sensor Test > Tray 3 No Paper. 2. Does the number on the Control Panel increase by 1 every time the Actuator is activated? Replace the MCU Board. Go to step 7. 7 1. Check the wiring harness connectors P/J421, P/J4212, and P/ J42121 between the No Paper Sensor and the Tray 3 Feeder Board. 2. Are the connectors securely connected? Go to step 8. Reconnect the connectors. 8 Check the No Paper Sensor signal. 1. Disconnect P/J421 from the Optional Feeder Board. 2. Is there +3.3 V across ground <=> J421-3 pin? Go to step 9. Go to step 10. 9 Check the No Paper Sensor for operation. 1. Measure the voltage across ground <=> J421-5 pin on the Optional Feeder Board. 2. Does the voltage change when the No Paper Sensor is activated? Complete. Replace the MCU Board. 10 1. Check the wiring harness connectors P/J419, P/J273, and P/ J27 between the Optional Feeder Board and the MCU Board. 2. Are the connectors securely connected? Go to step 11. Reconnect the connectors. 11 Check the Registration Sensor Harness for continuity. 1. Disconnect P/J273 from the Feeder Unit Harness. 2. Disconnect P/J27 from the MCU Board. 3. Check continuity between P/J273 <=> P/J27. Go to step 12. Replace the Right Side Harness. 12 Check the Optional Feeder Board signal. 1. Disconnect P/J27 from the MCU Board. 2. Is there +3.3 V across ground <=> J27-B7 pin on the MCU Board? Replace the 550-Sheet Feeder. Replace the MCU Board.

← Xem tất cả mã lỗi Xerox Phaser 6180

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie