Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 072-216 — Xerox Phaser 6180

Code: 072-216

Description: Motor Error (Optional 550-Sheet Feeder) The Optional 550-Sheet Feeder Motor has failed. The following troubleshooting procedure applies to this error.
Causes: • MCU Board, PL9.2.13 • Right Side Harness, PL10.1.12 • 550-Sheet Feeder, PL13.1.1 • Feed Roll, PL13.2.10 • Optional Feeder Board, PL13.3.6 • Optional Feeder Drive Assembly PL13.3.10 • Retard Roll, PL13.4.10
Remedy: 1 1. Check the paper tray for correct installation. 2. Is the tray correctly installed? Go to step 3. Reseat the paper tray. Go to step 2. 2 Does the error still occur when the printer is turned On? Go to step 3. Complete. 3 1. Check the Feed Rollers and Retard Rollers for rotation. 2. Do the Rollers rotate smoothly? Go to step 4. Replace the defective Roller(s). 4 1. Check the wiring harness connectors P/J422, P/J4221, and P/ J4222 between the Tray 3 Feeder Board and the Tray 3 Feeder Drive. 2. Are the connectors securely connected? Go to step 5. Reconnect the connectors. Go to step 5. 5 1. Perform the Tray 3 Feed Motor test: Service Mode > Printer Diag > Engine Diag > Motor Test > Tray 3 Feed Motor. Close the Front Door while running the Tray 3 Feed Motor. 2. Does the Tray 3 Motor operate properly? Replace the MCU Board. Go to step 6. 6 1. Check the Tray 3 Feeder Unit for correct installation. 2. Is the Tray 3 Feeder Assembly correctly installed? Go to step 7. Reseat the Tray 3 Feeder Unit. Go to step 7. 7 Does the error still occur when the printer is turned On? Go to step 8. Complete. 8 1. Check the wiring harness connectors P/J422 and P/J4222 between the Optional Feeder Board and the Optional Feeder Drive Assembly. 2. Are the connectors securely connected? Go to step 9. Reconnect the connectors. Go to step 9. 9 1. Check the wiring harness connectors P/J419, P/J273, and P/ J27 between the Optional Feeder Board and the MCU Board. 2. Are the connectors securely connected? Go to step 10. Reconnect the connectors. Go to step 10. 10 Check the Right Side Harness for continuity. 1. Disconnect P/J273 from the Feeder Unit harness. 2. Disconnect P/J27 from the MCU Board. 3. Check continuity between P/J273 <=> P/J27. Go to step 11. Replace the Right Side Harness. 11 Check the Optional Feeder Board signal. 1. Disconnect P/J27 from the MCU Board. 2. Is there +24 V across ground <=> J27-B4/J27-B5 pin on the MCU Board when the Interlock Switch is activated? Replace the 550-Sheet Feeder. Replace the MCU Board.

← Xem tất cả mã lỗi Xerox Phaser 6180

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie