Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 093-919 ... 093-922 — Xerox Phaser 6180

Code: 093-919 ... 093-922

Description: Remove Print Cartridge Tape (Yellow/Magenta/Cyan/Black) The Print Cartridge (Yellow/Magenta/Cyan/Black) tape was not removed when a new Print Cartridge is installed. The following troubleshooting procedure applies to these errors. • Chain Link 093-919: Check Yellow Cartridge • Chain Link 093-920: Check Magenta Cartridge • Chain Link 093-921: Check Cyan Cartridge • Chain Link 093-922: Check Black Cartridge
Causes: • Print Cartridge (Y/M/C/K), PL5.1.17-20 • Dispenser, PL5.2.10 • MCU Board, PL9.2.13 • Top LV Harness, PL10.1.3
Remedy: 1 1. Check the Print Cartridge tape. 2. Has the tape been removed? Go to step 2. Remove the tape on the Print Cartridge. Go to step 2. 2 Does the error still occur? Go to step 3. Complete. 3 1. Replace the Print Cartridge. 2. Does the error still occur? Go to step 4. Complete. 4 Perform the Toner Motor test: Service Mode > Engine Diag > Motor Test > Toner Motor. • Yellow Toner Motor • Magenta Toner Motor • Cyan Toner Motor • Black Toner Motor While testing the Toner Motor, close the Interlock Harness. Check the gear of the Auger for damage. If the gear is damaged, replace the Dispenser Motor. Go to step 5. 5 1. Check the Dispenser wiring harness connectors. • Yellow: P/J18 and P/J181 • Magenta: P/J18 and P/J182 • Black: P/J18 and P/J183 • Cyan: P/J18 and P/J184 2. Are the connectors securely connected? Go to step 6. Reconnect the connectors. Go to step 6. 6 Does the error still occur? Go to step 7. Complete. 7 Check the Top LV Harness for continuity. 1. Disconnect P/J Harnesses. • Yellow: P/J18 and P/J181 • Magenta: P/J18 and P/J182 • Black: P/J18 and P/J183 • Cyan: P/J18 and P/J184 2. Check continuity between P/J connectors: • Yellow: P/J18 <=> P/J181 • Magenta: P/J18 <=> P/J182 • Black: P/J18 <=> P/J183 • Cyan: P/J18 <=> P/J184 Go to step 8. Complete. 8 Check the Dispenser signal. 1. Disconnect P/J18 from the MCU Board. 2. When the Interlock Switch is activated, is there +24 V across: • Ground <=> P/J18-A1/P/J18-A2 pin (Yellow) • Ground <=> P/J18-A7/P/J18-A8 pin (Magenta) • Ground <=> P/J18-B1/P/J18-B2 pin (Black) • Ground <=> P/J18-B7/P/J18-B8 pin (Cyan) Replace the Dispenser. Replace the MCU Board.

← Xem tất cả mã lỗi Xerox Phaser 6180

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie