Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 092-651 — Xerox Phaser 6180 MFP

Code: 092-651

Description: ADC Sensor Error (Error Code 02) The ADC Sensor has detected density error. The following troubleshooting procedure applies to this error.
Causes: • Front Cover Harness, PL1.2.13 • Transfer Unit, PL4.1.1 • Laser Unit, PL5.1.12 • Print Cartridge (C/M/Y/K), PL5.1.17-20 • MCU Board, PL9.2.13 • Right Side Harness, PL10.1.12
Remedy: 1 1. Check the Transfer Unit for correct installation. 2. Is the Transfer Unit correctly installed? Go to step 3. Reseat the Transfer Unit. Go to step 2. 2 Does the error still occur when the printer is turned On? Go to step 3. Complete. 3 1. Check the Print Cartridges for correct installation. 2. Are the Print Cartridges correctly installed? Go to step 5. Reseat the Print Cartridges. Go to step 4. 4 Does the error still occur when the printer is turned On? Go to step 5. Complete. 5 Check the toner density and compare the density of four colors toner. 1. Check the toner density. Perform Gradation Test Print: Service Mode > Printer Diag > Test Print > Gradation ESS. 2. Is there light color on the print? Go to step 6. Replace the MCU Board. 6 Check the Solenoid in the Transfer Unit for operation. 1. Perform the ADC Sensor Solenoid test: Service Mode > Printer Diag > Engine Diag > Motor Test > ADC (CTD) Sensor Solenoid. 2. Perform the ADC Sensor LED test: Service Mode > Printer Diag > Engine Diag > Motor Test > ADC (CTD) Sensor LED. 3. Does the ADC Sensor operate properly? Go to step 11. Go to step 7. 7 1. Check the wiring harness connectors P/J27, P/J272, and P/ J2721 between the MCU Board and the Transfer Unit. 2. Are the connectors securely connected? Go to step 8. Reconnect the connectors. Go to step 10. 8 Check the Front Cover Harness for continuity. 1. Disconnect P/J2721 from the Transfer Unit. 2. Disconnect P/J272 from the Right Side Harness. 3. Check continuity between P/J2721 <=> P/J272. Go to step 9. Replace the Front Cover Harness. 9 Check the Right Side Harness for continuity. 1. Disconnect P/J27 from the MCU Board. 2. Disconnect P/J272 from the Front Cover Harness. 3. Check continuity between P/J27 <=> P/J272. Go to step 10. Replace the Right Side Harness. 10 Check the ADC Sensor signal. 1. Disconnect P/J27 from the MCU Board. 2. Is there +5 V across ground <=> J27-A7 pin on the MCU Board? Replace the Transfer Unit. Replace the MCU Board. 11 Check the Deve Motor for operation. 1. Perform the Deve Motor test: Service Mode > Printer Diag > Engine Diag > Motor Test > Deve Motor. Close the Front Cover while running the test. 2. Does the Deve Motor function normally? Go to step 13. Go to step 12. 12 1. Replace the Main Drive Assembly. 2. Does the error still occur when the printer is turned On? Replace the MCU Board. Complete. 13 1. Replace the corresponding Print Cartridge. 2. Does the error still occur when the printer is turned On? Replace the Laser Unit. Complete.

← Xem tất cả mã lỗi Xerox Phaser 6180 MFP

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie