Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 202 ... 205 — Xerox Phaser 6300

Code: 202 ... 205

Description: Replace [Y] [M] [C] [K] Toner Cartridge or [Y] [M] [C] [K] Toner Is Low An empty cartridge (Code 202~205), a metered cartridge installed in a non-metered printer, an unsupported high-capacity cartridge (Code 224~227), or a fatal error within the cartridge or printer can cause this error condition. Check for an error code in the help text prior to troubleshooting this error message. For codes 90~99, a different troubleshooting procedure is provided on. When no jobs are being sent to the printer, the [Y] [M] [C] [K] Toner Cartridge Empty message displays on the Control Panel. This warning allows continued printing in black and white (Run Black) mode for a short period of time. Once the color cartridges are empty, the message changes to Replace [Y] [M] [C] [K] Toner Cartridge, and the printer enters a hard stop condition. Code 202, 224: Replace Cyan Toner Cartridge Code 203, 225: Replace Magenta Toner Cartridge Code 204, 226: Replace Yellow Toner Cartridge Code 205, 227: Replace Black Toner Cartridge
Causes: • No Toner Sensor, PL7.2.5 • Toner Cartridge Holder, PL7.2.1 • TNR Harness, PL7.2.18
Remedy: 1 Replace the affected Toner Cartridge. Does the error persist? Go to Step 2. Complete 2 Check the No Toner Sensor signals. Disconnect P/J51. Is the signal less than +0.2 V for the affected sensor? J51-A8 <=> J51-A7 Yellow J51-A5 <=> J51-A4 Magenta J51-A2 <=> J51-A1 Cyan J51-A11 <=> J51-A10 Black Go to Step 5 Go to Step 3 3 Check the TNR Harness sensor connections J701 (Y), J702 (M), J703 (C), J704 (K) <=> J51 for continuity. Go to Step 4 Replace the TNR Harness. 4 Test the No Toner Sensor. Run the Service Diagnostics Toner Low/ Empty test on the affected cartridge. If the test fails, check the sensor connector, if the connector is ok, replace the Toner Sensor. Does the error persist? Go to Step 5. Complete 5 Test the Toner Motor. 1. Close the Interlock Switch while testing. NOTE: Run this test for ONLY 5 seconds to avoid packing the toner. 2. Run the Service Diagnostics Toner Motor test for the affected cartridge. Does the Toner Motor function correctly? Check the toner stirring auger or gear for damage. Replace if necessary. Go to Step 6. 6 Is the auger tube of the problem color full of toner near the hopper end? Go to Step 7. Inspect the toner cartridge for dispense problems. 7 Check the Engine Control Board. Disconnect P/J51. 1. Close the Interlock Switch while testing. 2. Is there +24 V for the Toner Motor? P51-B21 <=> ground Yellow P51-B26 <=> ground Magenta P51-B31 <=> ground Cyan J51-B36 <=> ground Black Is there +24 V to the affected Toner Motor? Go to Step 8. Replace the Engine Control Board. 8 Check the TNR Harness Toner Motor connections for continuity. Disconnect P/J51 and P511 (Y), P512 (M), P513 (C), 514 (K). Is the harness conductive? Go to Step 9 Replace the Toner Harness. 9 Replace the Toner Cartridge Holder for the affected color. Does the error persist? Replace the Engine Control Board. Complete

← Xem tất cả mã lỗi Xerox Phaser 6300

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie