Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 077-107, 077-108 — Xerox Phaser 6500

Code: 077-107, 077-108

Description: IOT Duplex Misfeed JAM / IOT Duplex JAM
Causes: • Left Side Harness Assy (PL3.1.18) • Option Harness Assy (PL3.1.20) • Regi Roller Assy (PL3.2.9) • Regi Metal Roller (PL3.2.10) • Duplex Roller Assy (PL11.2.9) • Registration Sensor (Sensor Photo) (PL3.2.13) • Fuser Assy (PL6.1.1) • MCU Board (SFP PL8.2.13; MFP PL8.3.6) • Duplex Unit (PL11.1.1)
Remedy: 1 Check the Front Cover for latching. Open and close the Front Cover, then check the latching. Does the error still occur when printing? Go to step 2. Complete. 2 Check after resetting the Fuser Assy. Reseat the Fuser Assy. Does the error still occur when printing? Go to step 3. Complete. 3 Reseat the Duplex Unit. Does the error still occur when printing? Go to step 4. Complete. 4 Perform the procedure “Duplex Exit Motor” on page 4-39 to check the Exit Drive Assy operation. Does the Exit Drive Assy operate properly? Go to step 5. Replace the Duplex Unit. 5 Perform the procedure “Duplex Motor” on page 4-41 to check the Duplex Drive Assy operation. Does the Duplex Drive Assy operate properly? Go to step 6. Replace the Duplex Unit. 6 Perform the procedure “Duplex Clutch” on page 4-40 to check the Duplex Clutch operation. Does the Duplex Clutch operate properly? Go to step 7. Replace the Duplex Unit. 7 Perform the procedure “Registration Sensor” on page 4-22 to check the Registration Sensor for operation. Does the number on the screen increase by one when you operate the Registration Input Actuator? Go to step 8. Go to step 10. 8 Turn the Duplex Roller Assy with your finger to check for shape and operation. Is the Duplex Roller Assy seated correctly? Also, is it free of contamination and/or damage, and does it rotate smoothly? Go to step 9. Replace Duplex Unit. 9 Check the Option Harness Assy for continuity Disconnect J27 from MCU Board. Disconnect P272 from Option Harness Assy. Is each cable of J27 <=> P272 continuous? Go to step 14. Replace Option Harness Assy. 10 Check the connections between the MCU Board and Registration Sensor. Are P/J23 and P/J232 connected correctly? Go to step 11. Reconnect P/J23 and/or P/J232 correctly. 11 Check the Left Side Harness Assy for continuity. Disconnect J23 from the MCU Board. Disconnect J232 from the Regis12 Disconnect J23 from the MCU Board and measure the voltage across P23-3 <=> ground on the MCU Board. Is the voltage about +3.3 VDC? Go to step 13. Replace the MCU Board. 13 Check the voltage across P23-5 <=> ground on the MCU Board. Remove the Lower Chute Assembly to check the operation of the Registration Sensor. Does the voltage change when you operate the Registration Input Actuator? Replace the MCU Board. Replace the Registration Sensor. 14 Check after replacing Duplex Unit. Replace Duplex Unit. Does the error still occur when printing? Go to step 15. Complete. 15 Check after replacing Fuser Assy. Replace Fuser Assy. Does the error still occur when printing? NOTE: After replacement, be sure to clear life counter value. Replace the MCU Board. Complete.tration Sensor. Is each cable of J23 <=> J232 continuous? Go to step 12. Replace the Left Side Harness Assy. (PL 3.1.18)

← Xem tất cả mã lỗi Xerox Phaser 6500

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie