Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 092-310 — Xerox Phaser 6500

Code: 092-310

Description: IOT CTD (ADC) Sensor Error
Causes: • Imaging Unit (PL4.1.21) • Dispenser Assy (PL5.1.1) • Motor Frame Assy (PL5.1.2) • Dispenser Motor Assy (PL5.1.3) • Toner Cartridge (Y) (PL5.1.24) • Toner Cartridge (M) (PL5.1.23) • Toner Cartridge (C) (PL5.1.22) • Toner Cartridge (K) (PL5.1.21) • Toner Motor Harness Assy (PL5.1.25) • Transfer Belt (PL6.1.7) • MCU Board (SFP PL8.2.13; MFP PL8.3.6)
Remedy: 1 Is the shipping protection sheet still on the Imaging Unit? Remove the protection sheet. Go to step 2. 2 Open the Front Cover and check the ADC Sensor Window. Is the ADC Sensor window dirty? Go to step 3. Go to step 4. 3 Turn off the power, and gently wipe the ADC Sensor window with a clean dry cloth or cotton swab. After wiping the window, close the Front Cover. Does the error still occur when the power is turned Off and On? Go to step 4. Complete. 4 Reseat the Toner Cartridges (Y, M, C and K), and check that the lock key is in the lock position. Does the error still occur when the power is turned Off and On? Go to step 5. Complete. 5 Perform the procedure gToner Motorsh on page 4-31to check the Toner Motors (Y, M, C and K) for rotation. Does each Toner Motor function normally? Go to step 6. Go to step 7. 6 Check the gears of the Dispenser Assy for shape and operation. Are the shape and operation of the gears of the Dispenser Assy normal? Go to step 11. Replace the Dispenser Assy. 7 Check the connectors between the MCU Board and Toner Motors (Y, M, C and K). Are the following connected correctly? • P/J18 • P/J181(Y) • P/J182(M) • P/J19 • P/J191(C) • P/J192(K) Go to step 9. Reconnect all the connectors, then go to step 8. 8 Does the error still occur when the power is turned Off and On? Go to step 9. Complete. 9 Check the Toner Motor Harness Assy for continuity. Disconnect J18 and J19 from the MCU Board. Disconnect J181(Y)/J182(M)/J191(C)/ J192(K) from the Toner Motors. Is each wire of J18 <=> J181/182 continuous? Is each wire of J19 <=> J191/192 continuous? Go to step 10. Replace the Toner Motor Harness Assy. 10 Check the power to the Dispenser Motor Assy. Disconnect J18 from the MCU Board and measure the voltage across P18-3 <= > ground on the MCU Board. Does the voltage measure about +24 VDC when the interlock switch (Interlock Harness Assy) is pushed? Replace the Dispenser Assy. Replace the MCU Board. 11 Reseat the Imaging Unit. Does the error still occur when the power is turned Off and On? Go to step 12. Complete. 12 Replace the Toner Cartridge (Y, M, C or K), and check that the lock key is in the lock position. Does the error still occur when the power is turned Off and On? Go to step 13. Complete. 13 Replace the Imaging Unit. Does the error still occur when the power is turned Off and On? Go to step 14. Complete. 14 Reseat the Transfer Belt. connectors? Does the error still occur when the power is turned Off and On? Replace the Transfer Belt. Complete.

← Xem tất cả mã lỗi Xerox Phaser 6500

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie