Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 12-221-00, 312.222.01, 312.224.01 — Xerox Phaser 6700

Code: 12-221-00, 312.222.01, 312.224.01

Description: Finisher Failure - Rear Tamper Home Position Rear Tamper Home Sensor state change not detected within the specified time after Rear Tamper moves from home position. • 12-221-00 Finisher Failure • 312.222.01 Finisher Rear Tamper Home Sensor On failure • 312.224.01 Finisher Rear Tamper Home Sensor Off failure
Causes: • MCU Board, PL10.2.18 • Finisher Main Board, PL14.4.12 • Compile Tray, PL14.8.1 • Rear Tamper Home Sensor, PL14.8.9 • Tamper Motor, PL14.8.18 • MOT1 Harness, PL14.11.3 • SNR1 Harness, PL14.11.5
Remedy: 1 Check the Rear Tamper motion by gently moving the tamper. The tamper moves freely. Go to Step 2. Replace the Compile Tray. 2 Test Rear Tamper Home Sensor using dc330 (012-032) and gently moving the front tamper in and out of the sensing area. The sensor signal changes (On/Off). Go to Step 7. Go to Step 3. 3 With Rear Tamper Home Sensor turned On in diagnostics, check for 5V at P/J8882-1. Is 5 V available at P/J8882-1? Replace the Front Tamper Home Sensor. Go to Step 4 4 Check Finisher Main Board connection P/J8988. The connection is secure and undamaged. Go to Step 5. Secure the connection. 5 Check SNR1 harness continuity between P/J8988 and P/J8882. The harness is undamaged. Go to Step 6. Replace the harness. 6 With Rear Tamper Home Sensor turned On in diagnostics, check for 5V at P/J8988-9 on the Finisher Main Board. Is 5 V available at P/J8988-9? Replace the MCU Board. Replace the Finisher Main Board. 7 Test the Rear Tamper Motor using dc330 (012-016). The motor rotates (On/Off). Go to Step 12. Go to Step 8. 8 Check MOT1 harness continuity between P/J8983 on the Finisher Main Board and P/J8883 on the Tamper Motor. The harness is undamaged. Go to Step 9. Replace the harness. 9 With the Rear Tamper Motor turned On in diagnostics, check for 24V at P/J8983-6. Is 24V available at P/J8983-6? Replace the Front Tamper Motor. Go to Step 10. 10 Check for 24V at P/J8980-1 on the Finisher Main Board. Is 24V available at P/J8980-1. Replace the MCU Board. Go to Step 11. 11 Remove the Finisher LVPS harness and check continuity between P/ J591 on the LVPS and P/J8980 on the Finisher Main Board. The harness is undamaged. Replace the Finisher LVPS. Replace the harness. 12 Replace the Finisher Main Board. Does the error persist? Replace the MCU Board. Complete.

← Xem tất cả mã lỗi Xerox Phaser 6700

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie