Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 312.283.01, 312.284.01 — Xerox Phaser 6700

Code: 312.283.01, 312.284.01

Description: Finisher Failure - Set Clamp Home Position Set Clamp Home Sensor state change not detected within the specified time. • 312.283.01 Finisher Eject Clamp Home Sensor On failure • 312.284.01 Finisher Eject Clamp Home Sensor Off failure
Causes: • MCU Board, PL10.2.18 • Set Clamp Home Sensor, PL14.4.3 • Set Clamp Cam Actuator, PL14.4.6 • Set Clamp Clutch, PL14.5.25 • Finisher Main Board, PL14.4.12 • Eject Motor, PL14.5.6 • SNR2 Harness, PL14.11.6 • MOT2 Harness, PL14.11.4
Remedy: 1 Check eject clamp motion by rotating the Eject Clamp Drive gears. The eject clamp moves freely. Go to Step 2. Repair any damaged parts. 2 Test Set Clamp Home Position Sensor using dc330 (012-037) and rotating the set clamp cam actuator in and out of the sensing area. The sensor signal changes (On/Off). Go to Step 7. Go to Step 3. 3 With Set Clamp Home Position Sensor turned On in diagnostics, check for 5V at P/J8871-1. Is 5 V available at P/J8871-1? Replace the Set Clamp Home Position Sensor. Go to Step 4 4 Check Finisher Main Board connection P/J8988. The connection is secure and undamaged. Go to Step 5. Secure the connection. 5 Check SNR2 harness continuity between P/J8989 and P/J8870. The harness is undamaged. Go to Step 6. Replace the harness. 6 With Set Clamp Home Position Sensor turned On in diagnostics, check for 5V at P/J8989-3B on the Finisher Main Board. Is 5 V available at P/J8989-3B? Replace the MCU Board. Replace the Finisher Main Board. 7 Test the Eject Motor using dc330 (012-025). The motor rotates (On/Off). Go to Step 10. Go to Step 8. 8 Check MOT2 harness continuity between P/J8984 on the Finisher Main Board and P/J8878 on the Eject Motor. The harness is undamaged. Go to Step 9. Replace the harness. 9 Check for 24V at P/J8884-5 and P/J8884-5. Is 24V available at P/J8884-5 and P/J8884-5? Replace the Eject Drive Assy. Go to Step 10. 10 Test the Set Clamp Clutch Z34 using dc330 (012-021). The clutch clicks (On/Off). Go to Step 14. Go to Step 11. 11 Check MOT2 harness continuity between P/J8984 on the Finisher Main Board and P/J8877 on the Set Clamp Clutch. The harness is undamaged. Go to Step 12. Replace the harness. 12 Check for 24V at P/J8884-4 on the Finisher Main Board. Is 24V available at P/J8884-4? Replace the MCU Board. Go to Step 13. 13 Remove the Finisher LVPS harness and check continuity between P/ J591 on the LVPS and P/J8980 on the Finisher Main Board. The harness is undamaged. Replace the Finisher LVPS. Replace the harness. 14 Replace the Finisher Main Board. Does the error persist? Replace the MCU Board. Complete.

← Xem tất cả mã lỗi Xerox Phaser 6700

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie