Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 31 — Xerox Phaser 7700

Code: 31

Description: 04-347 ERROR 31 Accumulator Belt HOME POSITION FAILURE
Remedy: Lower the Main Release Lever and return to the upright position to reestablish electrical connections to the belt. Open the RH Door and defeat the interlock switch. Look for rotation of the Accumulator Belt during the following test. Run the “Belt Edge Learn” test. Did the Accumulator Belt rotate? Y↓N→ Remove the Accumulator Belt Assembly. CautionRemoving the Accumulator Belt Assembly allows ambient light into the print cartridge area. Avoid exposing the print cartridge drums to light. Manually rotate the gear that drives the Accumulator Belt. Does it move freely? Y↓N→ Inspect the Accumulator Belt Cleaner Waste Auger for packed toner. Is the area inside the auger relatively clear of toner? Y↓N→ Note It is easy to spill toner in the next step. Remove the Waste Toner Cartridge. Run the “Agitator Motor Test.” Does the Waste Toner Agitator Motor rotate? Y↓N→ Measure the voltage at the Engine Control Board J404B-3. Does the voltage measure +24 VDC? Y↓N→ Measure the voltage at the Engine Control Board J408-7. Does the voltage measure +24 VDC? Y↓N→ Check for +24 VDC at the supply using the “Troubleshooting +24 VDC LVPS” procedure in the Troubleshooting Section, Troubleshooting the +24 VDC LVPS Replace the Engine Control Board. Repeat the “Agitator Motor” test while measuring the voltage at the Engine Control Board J404B-4. Does the voltage measure 0 VDC when the test is run and +24 VDC when the test is not run? Y↓N→ Replace the Engine Control Board. Replace the Waste Toner Agitator Motor. Using a Type II toner vacuum cleaner, vacuum out the Waste Auger Assembly. Replace the Waste Toner Cartridge. Recheck the gear that drives the Accumulator Belt for freedom of rotation. Does it move freely now? Y↓N→ Replace the Waste Auger Assembly. Reinstall all parts and assemblies and verify printer operation. If problem persists, resume this procedure at next line below. Remove the e-clip and remove any one of the Waste Auger Drive Gears. Again, manually rotate the gear that drives the Accumulator Belt. Does it move freely now? Y↓N→ Replace the Accumulator Belt Drive Assembly. Replace the Waste Auger Assembly. Run the “Accumulator Belt Motor” test. Does the Accumulator Belt Motor rotate? Y↓N→ Inspect P530 on the Engine Control Interface Board for proper seating. If the problem persists, replace the Accumulator Belt Drive Assembly. If the problem continues to persist, Replace the Engine Control Board. Replace the Accumulator Belt Assembly. Replace the Accumulator Belt Assembly. CautionIf the Accumulator Belt is damaged, determine the cause of the damage before installing a new Accumulator Belt Assembly. Visually inspect the Accumulator Belt area inside the printer and inside the LH door for foreign object or damage parts. It may be necessary to query the user for additional information as to likely causes. If the problem persists, replace the Engine Control Board.

← Xem tất cả mã lỗi Xerox Phaser 7700

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie