Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 30 — Xerox Phaser 7750

Code: 30

Description: Accumulator Belt Home Position Took Too Long, Code 30 Accumulator Belt Home Position Failure, Code 31 The accumulator belt home sensor did not detect the belt home signal. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed.
Causes: • Belt Cleaner • Accumulator Belt Motor • Waste Toner • Auger Assembly • Interface board • Engine Control Board
Remedy: If the accumulator belt is damaged, determine the cause of the damage before installing a new assembly. • Visually inspect the accumulator belt area inside the printer and inside the left hand door for foreign objects or damaged parts. • Inspect the belt steering mechanism to determine if it is operable. • It may be necessary to query the user for additional information as to likely causes.
1 Have the accumulator belt shipping restraints been completely removed? Go to step 2. Remove the restraints. 2 1. Enter service diagnostics and run the Clear Tech Rep Fault 04-346 procedure. 2. Enter the Adjustments/Calibrations menu and run the Belt Edge Learn Test with the right hand door open and the door interlock held actuated. 3. Does the accumulator belt rotate during the test? Go to step 3. Go to step 6. 3 1. Remove the accumulator belt assembly. Caution: Removing the accumulator belt assembly allows light into the imaging unit area, avoid exposing the imaging units to light. 2. Is the belt home marker present? This is a 7 mm, square, silver patch on the rear edge, inside the belt. Rotate the belt if you cannot see the marker. Go to step 4. Replace the accumulator belt assembly. 4 1. On the accumulater belt assembly, rotate the belt drive gear in the normal process direction until the belt home marker is positioned beneath the belt home sensor. 2. Reinstall the belt assembly. 3. Enter service diagnostics and run the Accum MOB Sensor test. 4. Is gMOB sensor is Hh displayed? Replace in the following order: • engine control interface board • engine control board Go to step 5. 5 1. Replace the accumulator belt assembly. 2. Retest. 3. Does error 30 return? Troubleshoot and repair using the Reflective Sensor Procedure on pg. 3-45. Complete. 6 1. Partially remove the accumulator belt assembly. 2. Manually rotate the drive gear clockwise. 3. Does the belt turn freely? Go to step 14. Go to step 7. 7 1. Inspect the a.ccumulator belt cleaner and waste auger for packed toner. 2. Are the belt cleaner and auger clean and free of toner? 3. Do the gears rotate freely? Go to step 9. Go to step 8. 8 1. Using a Type II Toner Vacuum, vacuum out the belt cleaner and waste auger. 2. Is the actuating lever broken off of the belt cleaner toner gate? Replace the belt cleaner assembly. Go to step 9. 9 1. Remove the waste toner cartridge. 2. Enter service diagnostics and run the Agitator Motor test. 3. Does the motor operate correctly? Verify the waste toner cartridge is fully seated. Complete. Go to step 10. 10 1. Check the voltage at J532A16 on the harness. 2. Is the voltage +24 VDC? Go to step 12. Go to step 11. 11 1. Check the voltage at J43-12 on the harness. 2. Is the voltage +24 VDC? Replace the engine control board. Go to step 13. 12 1. Check the voltage at J532A17 on the harness. 2. Is the voltage +24 VDC? Replace the engine control board. Replace the waste toner agitator motor. 13 Is +24 VDC present at the low-voltage power supply board? Troubleshoot the wiring between the +24 VDC LVPS and the Engine Control Board. See "Troubleshooting the Low-Voltage Power Supplies". 14 1. Remove the accumulator belt assembly. 2. Enter Service Diagnostics and run the Accum Belt Motor test. 3. Does the motor turn? Diagnose and repair the mechanical condition binding the accumulator belt assembly. Since the accumulator belt drive motor is a servo motor, there are no voltage checks. This failure can be caused by 1 of 3 components. Replace and test in the following order: • motor • interface board • engine control board

← Xem tất cả mã lỗi Xerox Phaser 7750

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie