Code: 004-346, 004-347
Description: Accumulator Belt Home Position Fail Too Long or Out of Position The IBT Home Sensor does not detect the Belt Home signal or does not sense the Transfer Belt edge in the correct position. This procedure can be used for troubleshooting Chain Link code 004-346 or 004-347.
Remedy: 1 Have the Accumulator Belt shipping restrains been completely removed? Go to step 2. Remove the restraints. 2 1. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Perform the Clear Tech Rep Faults 04-346 procedure. 2. Enter the Adjustments/Calibrations menu and run the Belt Edge Learn Test with the Right-Hand Door open and the Door Interlock held actuated. 3. Does the Accumulator Belt rotate during the test? Go to step 3. Go to step 6. 3 CAUTION Removing the Accumulator Belt Assembly allows light into the Imaging Unit area, avoid exposing the Imaging units to light. 1. Remove the Accumulator Belt Assembly. 2. Is the Belt Home Marker present? Go to step 4. Replace the Accumulator Belt Assembly. 4 1. On the Accumulator Belt Assembly, rotate the Belt Drive Gear in the normal process direction until the Belt Home Marker is positioned beneath the Belt Home Sensor. 2. Reinstall the Belt Assembly. 3. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Run the Accum MOB Sensor test. 4. Is MOB Sensor is H displayed? Replace in the following order: 1. Engine Control Interface Board 2. Engine Control Board (MCU PWB) Go to step 5. 5 1. Replace the Accumulator Belt Assembly. 2. Retest. 3. Does error 30 return? Troubleshoot and repair using the Reflective Sensor Procedure (). Complete. 6 1. Partially remove the Accumulator Belt Assembly. 2. Manually rotate the Drive Gear clockwise. 3. Does the Belt turn freely? Go to step 14. Go to step 7. 7 1. Inspect the Accumulator Belt Cleaner and Waste Auger for packed toner. 2. Are the Belt Cleaner and Auger clean and free of toner? 3. Do the gears rotate freely? Go to step 9. Go to step 8. 8 1. Using a Type II Toner vacuum, vacuum out the Belt Cleaner and Waste Auger. 2. Is the Actuating Lever broken off of the Belt Cleaner Toner Gate? Replace the Belt Cleaner Assembly. Go to step 9. 9 1. Remove the Waste Toner Cartridge. 2. Enter Service Diagnostics and run the Agitator Motor test. 3. Does the Motor operate correctly? Verify the Waste Toner Cartridge is fully seated. Complete. Go to step 10. 10 1. Check the voltage at J537 on the harness. 2. Is the voltage +24 VDC? Go to step 12. Go to step 11. 11 1. Check the voltage at J537 on the harness. 2. Is the voltage +24 VDC? Replace the Engine Control Board (MCU PWB). Go to step 13. 12 1. Check the voltage at J537 on the harness. Replace the Engine Control Board (MCU PWB) Replace the Waste Toner Agitator Motor. 13 Is +24 VDC present at the Low-Voltage Power Supply Board? Troubleshoot the wiring between the +24 VDC LVPS and the Engine Control Board. Refer to Troubleshooting Low-Voltage Power Supplies procedure (). 14 1. Remove the Accumulator Belt Assembly. 2. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Run the Accumulator Belt Motor test. 3. Does the Motor run? Diagnose and repair the mechanical condition binding the Accumulator Belt Assembly. Since the Accumulator Belt Drive Motor is a servo motor, there are no voltage checks. This failure can be caused by 1 of 3 components. Replace and test in the following order: 1. Motor 2. Interface Board 3. Engine Control Board (MCU PWB)