Code: 012-243
Description: Booklet Knife Home Sensor On Fail Knife Home Sensor is not turned On after the lapse of 500ms from Clutch On while Booklet Knife is returning to Home.
Remedy: • Check the Knife Home Sensor for improper installation. • Check the Knife Home Sensor connectors for connection failure. • Check the Booklet Fold Motor connectors for connection failure. • Check the Knife Clutch connectors for connection failure. • Check the Knife Clutch for improper installation. • Check the Knife drive mechanism for a foreign substance.
Manually move the Booklet Tamper to both ends. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Run the Booklet Folder Roll Motor test. The Booklet Folder Roll Motor (PL 21.22) energizes. Y↓N→Check continuity between the Booklet Folder Roll Motor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Booklet Folder Roll Motor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Perform the Knife Solenoid test (PL 21.22). The Knife Solenoid actuates. Y↓N→Check continuity between the Knife Solenoid and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Solenoid (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Block/unblock the Knife Home Sensor (PL 21.22). The display changed. Y↓N→Check continuity between the Knife Home Sensor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Home Sensor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). If the problem continues, replace the Finisher PWB (PL 21.12).
Manually move the Booklet Tamper to both ends. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Run the Booklet Folder Roll Motor test. The Booklet Folder Roll Motor (PL 21.22) energizes. Y↓N→Check continuity between the Booklet Folder Roll Motor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Booklet Folder Roll Motor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Perform the Knife Solenoid test (PL 21.22). The Knife Solenoid actuates. Y↓N→Check continuity between the Knife Solenoid and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Solenoid (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Block/unblock the Knife Home Sensor (PL 21.22). The display changed. Y↓N→Check continuity between the Knife Home Sensor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Home Sensor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). If the problem continues, replace the Finisher PWB (PL 21.12).