Code: 012-261
Description: Booklet Knife Folding Sensor Fail When the Booklet Knife performs folding operation, the Knife Folding Sensor did not turn On within 400 msec. after Knife Solenoid On.
Remedy: • Check the Knife Folding Sensor for improper installation. • Check the Knife Folding Sensor connectors for connection failure. • Check the Booklet Fold Motor connectors for connection failure. • Check the Knife Solenoid connectors for connection failure. • Check the Knife Solenoid for improper installation. • Check the Knife drive mechanism for a foreign substance.
Manually move the Booklet Tamper to both ends. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Actuate the Booklet Folder Roll Motor alternately. The Booklet Folder Roll Motor (PL 21.22) energizes. Y↓N→Check continuity between the Booklet Folder Roll Motor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Booklet Folder Roll Motor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Enter Service Diagnostics Menu. Check the Knife Solenoid (PL 21.22). The Knife Solenoid actuates. Y↓N→Check continuity between the Knife Solenoid and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Solenoid (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Enter Service Diagnostics Menu. Block/unblock the Knife Home Sensor (PL 21.22). The display changed. Y↓N→Check continuity between the Knife Home Sensor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Home Sensor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12).
Manually move the Booklet Tamper to both ends. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Actuate the Booklet Folder Roll Motor alternately. The Booklet Folder Roll Motor (PL 21.22) energizes. Y↓N→Check continuity between the Booklet Folder Roll Motor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Booklet Folder Roll Motor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Enter Service Diagnostics Menu. Check the Knife Solenoid (PL 21.22). The Knife Solenoid actuates. Y↓N→Check continuity between the Knife Solenoid and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Solenoid (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12). Enter Service Diagnostics Menu. Block/unblock the Knife Home Sensor (PL 21.22). The display changed. Y↓N→Check continuity between the Knife Home Sensor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Knife Home Sensor (PL 21.22). If the problem continues, replace the Booklet PWB (PL 21.12). If the problem persists, replace Finisher PWB (PL 21.12).