Code: 012-303
Description: H-Transport Cover Open H-Transport Cover Interlock Sensor Open was detected.
Remedy: Check the following components: • The H-Transport Cover Interlock Sensor for improper installation • Check for obstruction in the between the H-Transport Cover and the H-Transport paper transport area • The H-Transport Cover Interlock Sensor connectors for connection failure • The Actuator part for deformation
Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Block and unblock the H-Transport Interlock Sensor (PL 21.25). The display changes. Y↓N→+5 VDC is measured between the H-Transport Interlock Sensor J8445-1 and -3. Y↓N→Disconnect P/J8396 on the Finisher PWB. +5 VDC is measured between Finisher PWB P/J8396-1 and -3. Y↓N→Replace the Finisher PWB (PL 21.3). Check for an open circuit between Finisher PWB P/J8396-3 and -1 and H-Transport Interlock Sensor J8445-1 and -3. +5 VDC is measured between Finisher PWB P/J8396-2 and ground. Y↓N→Replace the Finisher PWB (PL 21.3). +5 VDC is measure between H-Transport Interlock Switch J8454-2 and ground. Y↓N→Check the wire between the H-Transport Interlock Switch J8454-2 and the Finisher PWB P/J8396-2 for an open circuit or poor contact. +5 VDC is measured between H-Transport Interlock Switch J8454-1 and ground. Y↓N→Replace the H-Transport Interlock Switch (PL 21.24). +5 VDC is measured at the H-Transport Interlock Sensor J8445-2 and ground. Y↓N→Check for an open circuit between H-Transport Interlock Switch J8454-1 and HTransport Interlock Sensor J8445-2. Replace the H-Transport Interlock Sensor (PL 21.25). Check the following: • Alignment between the H-Transport Cover and the H-Transport Interlock Sensor. • Alignment between the H-Transport Cover and the H-Transport Interlock Switch. • The H-Transport Cover for proper installation • The Actuator for bending or alignment • The Magnets for proper mounting
Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Block and unblock the H-Transport Interlock Sensor (PL 21.25). The display changes. Y↓N→+5 VDC is measured between the H-Transport Interlock Sensor J8445-1 and -3. Y↓N→Disconnect P/J8396 on the Finisher PWB. +5 VDC is measured between Finisher PWB P/J8396-1 and -3. Y↓N→Replace the Finisher PWB (PL 21.3). Check for an open circuit between Finisher PWB P/J8396-3 and -1 and H-Transport Interlock Sensor J8445-1 and -3. +5 VDC is measured between Finisher PWB P/J8396-2 and ground. Y↓N→Replace the Finisher PWB (PL 21.3). +5 VDC is measure between H-Transport Interlock Switch J8454-2 and ground. Y↓N→Check the wire between the H-Transport Interlock Switch J8454-2 and the Finisher PWB P/J8396-2 for an open circuit or poor contact. +5 VDC is measured between H-Transport Interlock Switch J8454-1 and ground. Y↓N→Replace the H-Transport Interlock Switch (PL 21.24). +5 VDC is measured at the H-Transport Interlock Sensor J8445-2 and ground. Y↓N→Check for an open circuit between H-Transport Interlock Switch J8454-1 and HTransport Interlock Sensor J8445-2. Replace the H-Transport Interlock Sensor (PL 21.25). Check the following: • Alignment between the H-Transport Cover and the H-Transport Interlock Sensor. • Alignment between the H-Transport Cover and the H-Transport Interlock Switch. • The H-Transport Cover for proper installation • The Actuator for bending or alignment • The Magnets for proper mounting