Code: 310.380
Description: P/Roll Latch Motor Fault. When in the P/Roll Contact/Retract operation, the Latch Position Sensor detected a Latch position error of the P/Roll.
Remedy: • Turn the power Off and check whether the Fuser Assembly is installed properly. • Remove the Fuser Assembly and check the Drawer Connector between the Fuser Assembly and the Main Unit ( DJ600) for broken/bent pins, foreign substances, burns, and etc. • Check whether the MCU PWB connector P/J431 is connected properly.
Turn the power Off and remove the Rear Upper Cover. Disconnect the connector P592 of the MD PWB and open the Chassis Assembly. Turn the power On and enter Service Diagnostics (Entering Service Diagnostics). Turn On dc330 Component Control [010-009] (P/Roll Latch On) and DC330 [010-010] (P/Roll Latch Off) alternately. Does the Latch Motor rotate? Y↓ N→Is the voltage between the MD PWB P/J520-9 (+) and the GND +24VDC? Y↓ N→Go to +24VDC Power RAP. Turn the power Off, then measure the Latch Motor wire wound resistance. Disconnect the Latch Motor P/J254, then measure the following resistances. • Between Latch Motor P/J254 pin-2 and P/J254 pin-6 • Between Latch Motor P/J254 pin-1 and P/J254 pin-5 Is the resistance approx. 5.7 Ohm for each? (At 25° C / 77° F) Y↓ N→Replace the Fuser Assembly. Measure the resistance between the disconnected connector P/J254-1/2/5/6 and the Frame. Is the resistance infinite for all? Y↓ N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. If no problems are found, replace the following parts in sequence: • MD PWB • MCU PWB Press the Stop button. Turn On dc330 Component Control [010-009] (P/Roll Latch On) and DC330 [010-202] (P/Roll Latch Sensor), as well as DC330 [010-010] (P/Roll Latch Off) and DC330 [010-202] (P/Roll Latch Sensor) alternately. Does the display change between Low/High? Y↓ N→Is the voltage between the MCU PWB P/J431-4 (+) and the GND +1.2VDC? Y↓ N→Press the Stop button and turn the power Off. Remove the Fuser Assembly and check the connection between the DJ600-A8/A7 and the MCU PWB P/J431-4/5 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Fuser Assembly • MCU PWB Press the Stop button and turn the power Off. Remove the Fuser Assembly and check the connection between the DJ600-A6 and the MCU PWB P/J431-6 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Fuser Assembly • MCU PWB Turn the power Off and check the Latch Motor Gear for wear or damage. If no problems are found, replace the following parts in sequence: • MCU PWB • MD PWB
Turn the power Off and remove the Rear Upper Cover. Disconnect the connector P592 of the MD PWB and open the Chassis Assembly. Turn the power On and enter Service Diagnostics (Entering Service Diagnostics). Turn On dc330 Component Control [010-009] (P/Roll Latch On) and DC330 [010-010] (P/Roll Latch Off) alternately. Does the Latch Motor rotate? Y↓ N→Is the voltage between the MD PWB P/J520-9 (+) and the GND +24VDC? Y↓ N→Go to +24VDC Power RAP. Turn the power Off, then measure the Latch Motor wire wound resistance. Disconnect the Latch Motor P/J254, then measure the following resistances. • Between Latch Motor P/J254 pin-2 and P/J254 pin-6 • Between Latch Motor P/J254 pin-1 and P/J254 pin-5 Is the resistance approx. 5.7 Ohm for each? (At 25° C / 77° F) Y↓ N→Replace the Fuser Assembly. Measure the resistance between the disconnected connector P/J254-1/2/5/6 and the Frame. Is the resistance infinite for all? Y↓ N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. If no problems are found, replace the following parts in sequence: • MD PWB • MCU PWB Press the Stop button. Turn On dc330 Component Control [010-009] (P/Roll Latch On) and DC330 [010-202] (P/Roll Latch Sensor), as well as DC330 [010-010] (P/Roll Latch Off) and DC330 [010-202] (P/Roll Latch Sensor) alternately. Does the display change between Low/High? Y↓ N→Is the voltage between the MCU PWB P/J431-4 (+) and the GND +1.2VDC? Y↓ N→Press the Stop button and turn the power Off. Remove the Fuser Assembly and check the connection between the DJ600-A8/A7 and the MCU PWB P/J431-4/5 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Fuser Assembly • MCU PWB Press the Stop button and turn the power Off. Remove the Fuser Assembly and check the connection between the DJ600-A6 and the MCU PWB P/J431-6 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Fuser Assembly • MCU PWB Turn the power Off and check the Latch Motor Gear for wear or damage. If no problems are found, replace the following parts in sequence: • MCU PWB • MD PWB