Code: 312.171
Description: Top Tray Exit Sensor On Jam. Not in the Punch mode: The Top Tray Exit Sensor did not turn on within the specified time after Punch Out Sensor on. In Punch mode: The Top Tray Exit Sensor did not turn on within the specified time after the punching operation had begun.
Remedy: • Check Top Tray Exit for operation failure. • Check paper transportation failure due to a foreign substance/burr on the paper path. • Check transportation failure of non-standard paper.
Enter dc330 Component Control [012-115], Top Tray Exit Sensor (PL 24.36 Item 3). Select Start. Actuate the Top Tray Exit Sensor. The display changes. Y↓ N→Go to Finisher Top Tray Stacking Check the circuit of the Top Tray Exit Sensor. Refer to the Transmissive Sensor RAP for troubleshooting procedure. Select [012-007], Exit Motor (PL 24.43 Item 7). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher Drives Check the circuit of the Exit Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Select [012-011] or [012-012], Transport Gate Solenoid (PL 24.41 Item 37). Select Start. The Transport Gate Solenoid actuates. Y↓ N→Select Stop. Go to Finisher Transport, Top Tray Gating. Check the circuit of the Transport Gate Solenoid. Refer to the Set Gate Solenoid Open RAP for troubleshooting procedure. Select [012-001], Finisher Transport Motor (PL 24.41 Item 26). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher Drives Check the circuit of the Finisher Transport Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Check the following: • Ensure that the connectors shown in the circuit diagrams are securely connected and that the wires are not damaged. • Check the Exit Motor and its associated gears and belts for damage, contamination or misalignment. • Exit Drive Shaft for wear and a revolution failure • The Exit Pinch Rolls for wear and/or damage If the above checks are OK, then replace the Top Tray Exit Sensor. If the problem persists, replace the Finisher Main PWB.
Enter dc330 Component Control [012-115], Top Tray Exit Sensor (PL 24.36 Item 3). Select Start. Actuate the Top Tray Exit Sensor. The display changes. Y↓ N→Go to Finisher Top Tray Stacking Check the circuit of the Top Tray Exit Sensor. Refer to the Transmissive Sensor RAP for troubleshooting procedure. Select [012-007], Exit Motor (PL 24.43 Item 7). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher Drives Check the circuit of the Exit Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Select [012-011] or [012-012], Transport Gate Solenoid (PL 24.41 Item 37). Select Start. The Transport Gate Solenoid actuates. Y↓ N→Select Stop. Go to Finisher Transport, Top Tray Gating. Check the circuit of the Transport Gate Solenoid. Refer to the Set Gate Solenoid Open RAP for troubleshooting procedure. Select [012-001], Finisher Transport Motor (PL 24.41 Item 26). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher Drives Check the circuit of the Finisher Transport Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Check the following: • Ensure that the connectors shown in the circuit diagrams are securely connected and that the wires are not damaged. • Check the Exit Motor and its associated gears and belts for damage, contamination or misalignment. • Exit Drive Shaft for wear and a revolution failure • The Exit Pinch Rolls for wear and/or damage If the above checks are OK, then replace the Top Tray Exit Sensor. If the problem persists, replace the Finisher Main PWB.