Code: 312.172
Description: Top Tray Exit Sensor Off Jam. Top Tray Exit Sensor Off was not detected at the rear edge of paper within the specified time after Punch Out Sensor detected at the leading edge of the same paper. Top Tray Exit Sensor Off was not detected at the rear edge of paper within the specified time after the punching operation had begun.
Remedy: • Check Top Tray Exit for operation failure. • Check paper transportation failure due to a foreign substance/burr on the paper path. • Check transportation failure of non-standard paper.
Enter dc330 Component Control [012-115], Top Tray Exit Sensor (PL 24.36 Item 3). Select Start. Actuate the Top Tray Exit Sensor. The display changes. Y↓ N→Go to Finisher Transport, Top Tray Gating. Check the circuit of the Top Tray Exit Sensor. Refer to the Transmissive Sensor RAP for troubleshooting procedure. Select [012-007], Exit Motor (PL 24.43 Item 7). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher Drives. Check the circuit of the Exit Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Select [012-011] or [012-012], Transport Gate Solenoid (PL 24.41 Item 37). Select Start. The Transport Gate Solenoid actuates. Y↓ N→Select Stop. Go to Finisher Transport, Top Tray Gating. Check the circuit of the Transport Gate Solenoid. Refer to the Set Gate Solenoid Open RAP for troubleshooting procedure. Select [012-001], Finisher Transport Motor (PL 24.41 Item 26). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher H-Transport Drives. Check the circuit of the Finisher Transport Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Check the following: • Ensure that the connectors shown in the circuit diagrams are securely connected and that the wires are not damaged. • Check the Exit Motor and its associated gears and belts for damage, contamination or misalignment. • Exit Drive Shaft for wear and a revolution failure • The Exit Pinch Rolls for wear and/or damage If the above checks are OK, then replace the top Tray Exit Sensor. If the problem persists, replace the Finisher Main PWB.
Enter dc330 Component Control [012-115], Top Tray Exit Sensor (PL 24.36 Item 3). Select Start. Actuate the Top Tray Exit Sensor. The display changes. Y↓ N→Go to Finisher Transport, Top Tray Gating. Check the circuit of the Top Tray Exit Sensor. Refer to the Transmissive Sensor RAP for troubleshooting procedure. Select [012-007], Exit Motor (PL 24.43 Item 7). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher Drives. Check the circuit of the Exit Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Select [012-011] or [012-012], Transport Gate Solenoid (PL 24.41 Item 37). Select Start. The Transport Gate Solenoid actuates. Y↓ N→Select Stop. Go to Finisher Transport, Top Tray Gating. Check the circuit of the Transport Gate Solenoid. Refer to the Set Gate Solenoid Open RAP for troubleshooting procedure. Select [012-001], Finisher Transport Motor (PL 24.41 Item 26). Select Start. The motor energizes. Y↓ N→Select Stop. Go to Finisher H-Transport Drives. Check the circuit of the Finisher Transport Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Select Stop. Check the following: • Ensure that the connectors shown in the circuit diagrams are securely connected and that the wires are not damaged. • Check the Exit Motor and its associated gears and belts for damage, contamination or misalignment. • Exit Drive Shaft for wear and a revolution failure • The Exit Pinch Rolls for wear and/or damage If the above checks are OK, then replace the top Tray Exit Sensor. If the problem persists, replace the Finisher Main PWB.