Code: 312.213
Description: Stacker Tray Lower Limit Fault. Stacker descended lower than normal levels, below low limit height.
Remedy: • Check for obstructions under the tray. • Check the operation of the Stacker Height Sensor actuators. • Check the tray raise/lower mechanism for damage or contamination.
Height Sensor 1. The display changes. Y↓ N→Check the wire between J8873 pin 2 and P/J8988 pin 17 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 16 and 18 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 17 on the Finisher PWB and GND (Stacker Tray Control).Actuate the Stacker Height Sensor 1. The voltage changes. Y↓ N→Replace the Stacker Height Sensor 1 (PL 23.11). Replace the Finisher PWB. Execute dc330 Component Control [012-265], Stacker Height Sensor 2. Block and unblock the Stacker Height Sensor 2. The display changes. Y↓ N→Check the wire between J8874 pin 2 and P/J8988 pin 20 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 19 and 21 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 20 on the Finisher PWB and GND (Stacker Tray Control). Actuate the Stacker Height Sensor 1. The voltage changes. Y↓ N→Replace the Stacker Height Sensor 2 (PL 23.11). Replace the Finisher PWB. Execute dc330 Component Control [012-263], Stacker Encoder Sensor. Manually rotate the Encoder (PL 23.7) to block and unblock the sensor. The display changes. Y↓ N→Check the wire between J8875 pin 2 and P/J8988 pin 23 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 22 and 24 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 23 on the Finisher PWB and GND (Stacker Tray Control). Manually rotate the Encoder (PL 23.7) to block and unblock the Stacker Encoder Sensor. The voltage changes. Y↓ N→Replace the Stacker Encoder Sensor (PL 23.7). Replace the Finisher PWB. Execute dc330 Component Control [012-262], Stacker No Paper Sensor. Block and unblock the Sensor (PL 23.7). The display changes. Y↓ N→Check the wire between J8872 pin 2 and P/J8988 pin 14 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 13 and 15 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 14 on the Finisher PWB and GND (Stacker Tray Control). Actuate the Stacker No Paper Sensor. The voltage changes. Y↓ N→Replace the Stacker No Paper Sensor (PL 23.7). Replace the Finisher PWB. Replace the Finisher PWB.
Height Sensor 1. The display changes. Y↓ N→Check the wire between J8873 pin 2 and P/J8988 pin 17 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 16 and 18 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 17 on the Finisher PWB and GND (Stacker Tray Control).Actuate the Stacker Height Sensor 1. The voltage changes. Y↓ N→Replace the Stacker Height Sensor 1 (PL 23.11). Replace the Finisher PWB. Execute dc330 Component Control [012-265], Stacker Height Sensor 2. Block and unblock the Stacker Height Sensor 2. The display changes. Y↓ N→Check the wire between J8874 pin 2 and P/J8988 pin 20 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 19 and 21 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 20 on the Finisher PWB and GND (Stacker Tray Control). Actuate the Stacker Height Sensor 1. The voltage changes. Y↓ N→Replace the Stacker Height Sensor 2 (PL 23.11). Replace the Finisher PWB. Execute dc330 Component Control [012-263], Stacker Encoder Sensor. Manually rotate the Encoder (PL 23.7) to block and unblock the sensor. The display changes. Y↓ N→Check the wire between J8875 pin 2 and P/J8988 pin 23 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 22 and 24 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 23 on the Finisher PWB and GND (Stacker Tray Control). Manually rotate the Encoder (PL 23.7) to block and unblock the Stacker Encoder Sensor. The voltage changes. Y↓ N→Replace the Stacker Encoder Sensor (PL 23.7). Replace the Finisher PWB. Execute dc330 Component Control [012-262], Stacker No Paper Sensor. Block and unblock the Sensor (PL 23.7). The display changes. Y↓ N→Check the wire between J8872 pin 2 and P/J8988 pin 14 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 13 and 15 on the Finisher PWB (Stacker Tray Control). The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between P/J8988, pin 14 on the Finisher PWB and GND (Stacker Tray Control). Actuate the Stacker No Paper Sensor. The voltage changes. Y↓ N→Replace the Stacker No Paper Sensor (PL 23.7). Replace the Finisher PWB. Replace the Finisher PWB.