Code: 312.247
Description: Side Registration Sensor Off Fault. Side Registration Sensor not turned off after the lapse of 500msec from operation start. Side Registration Sensor is not turned off after the stop following Side Registration Sensor Off. Target Side Registration Sensor1 or Side Registration Sensor2 is not turned off at operation start.
Remedy: • The Actuator for deformation • The Side Reg 1 and 2 Sensors for improper installation • The Side Reg 1 and 2 Sensors connectors for connection failure • The Puncher Move Motor connectors for connection failure
Enter dc330 Component Control [012-071] and [012-073], Puncher Move Motor (PL 24.32 Item 26), alternately. Select Start. The Puncher Move Motor run. Y↓ N→Select Stop. Go to BSD 14 22 Finisher Punch Drive. Check continuity between the Puncher Move Motor and Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Puncher Move Motor (PL 24.32 Item 26). If the problem continues, replace the Finisher Main PWB. Select Stop. Select [012-200], Side Registration 1 Sensor (PL 24.32 Item 10). Select Start. Block/unblock the Side Reg 1 Sensor. The display changes. Y↓ N→Select Stop. Go to Finisher Booklet/ Punch Transport. Check continuity between the Side Reg 1 Sensor and Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Side Reg 1 Sensor (PL 24.32 Item 10). If the problem continues, replace the Finisher Main PWB. Select [012-201], Side Reg 2 Sensor (PL 24.32 Item 10). Select Start. Block/unblock the Side Reg 2 Sensor. The display changes. Y↓ N→Select Stop. Go to Finisher Booklet/ Punch Transport. Check continuity between the Side Reg 2 Sensor and Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Side Reg 2 Sensor (PL 24.32 Item 10). If the problem continues, replace the Finisher Main PWB. Select Stop. Check the following: • The Puncher Move Motor Belt for improper tension • The Puncher Move Motor Belt for disengagement If the above checks are OK, replace the Finisher Main PWB.
Enter dc330 Component Control [012-071] and [012-073], Puncher Move Motor (PL 24.32 Item 26), alternately. Select Start. The Puncher Move Motor run. Y↓ N→Select Stop. Go to BSD 14 22 Finisher Punch Drive. Check continuity between the Puncher Move Motor and Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Puncher Move Motor (PL 24.32 Item 26). If the problem continues, replace the Finisher Main PWB. Select Stop. Select [012-200], Side Registration 1 Sensor (PL 24.32 Item 10). Select Start. Block/unblock the Side Reg 1 Sensor. The display changes. Y↓ N→Select Stop. Go to Finisher Booklet/ Punch Transport. Check continuity between the Side Reg 1 Sensor and Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Side Reg 1 Sensor (PL 24.32 Item 10). If the problem continues, replace the Finisher Main PWB. Select [012-201], Side Reg 2 Sensor (PL 24.32 Item 10). Select Start. Block/unblock the Side Reg 2 Sensor. The display changes. Y↓ N→Select Stop. Go to Finisher Booklet/ Punch Transport. Check continuity between the Side Reg 2 Sensor and Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Side Reg 2 Sensor (PL 24.32 Item 10). If the problem continues, replace the Finisher Main PWB. Select Stop. Check the following: • The Puncher Move Motor Belt for improper tension • The Puncher Move Motor Belt for disengagement If the above checks are OK, replace the Finisher Main PWB.