Code: 312.265
Description: Booklet Knife Home Sensor Off Fault. When the Booklet Knife moves from Home position, the Knife Home Sensor did not turn Off within the specified time after Knife Solenoid On.
Remedy: • The Knife Home Sensor for improper installation • The Knife Home Sensor connectors for connection failure • The Booklet Fold Motor connectors for connection failure • The Knife Solenoid connectors for connection failure • The Knife Solenoid for improper installation • The Knife drive mechanism for a foreign substance
Manually move the Booklet Tamper to both ends. Enter dc330 Component Control [013-008] and [013-009], Booklet Folder Roll Motor (PL 24.58 Item 2), alternately. Select Start. The Booklet Folder Roll Motor energizes. Y↓ N→Select Stop. Go to Booklet Drive. Check continuity between the Booklet Folder Roll Motor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Booklet Folder Roll Motor (PL 24.58 Item 2). If the problem continues, replace the Booklet PWB (PL 24.51 Item 1). If the problem persists, replace Finisher PWB. Select Stop. Select dc330 Component Control [013-010], Booklet Knife Solenoid, (PL 24.58 Item 10). Select Start. The Knife Solenoid actuates. Y↓ N→Select Stop. Go to Booklet Knife Control. Check continuity between the Knife Solenoid and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Knife Solenoid (PL 24.58 Item 10). If the problem continues, replace the Booklet PWB (PL 24.51 Item 1). If the problem persists, replace Finisher Main PWB. Select Stop. Select dc330 Component Control [013-140], Booklet Knife Folding Sensor (PL 24.54 Item 3). Select Start. Block/unblock the Knife Folding Sensor. The display changed. Select Stop. Go to Booklet Knife Control. Check continuity between the Knife Folding Sensor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Knife Folding Sensor (PL 24.54 Item 3). If the problem continues, replace the Booklet PWB (PL 24.51 Item 1). If the problem persists, replace Finisher Main PWB. Select Stop. If the problem continues, replace the Finisher Main PWB.
Manually move the Booklet Tamper to both ends. Enter dc330 Component Control [013-008] and [013-009], Booklet Folder Roll Motor (PL 24.58 Item 2), alternately. Select Start. The Booklet Folder Roll Motor energizes. Y↓ N→Select Stop. Go to Booklet Drive. Check continuity between the Booklet Folder Roll Motor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Booklet Folder Roll Motor (PL 24.58 Item 2). If the problem continues, replace the Booklet PWB (PL 24.51 Item 1). If the problem persists, replace Finisher PWB. Select Stop. Select dc330 Component Control [013-010], Booklet Knife Solenoid, (PL 24.58 Item 10). Select Start. The Knife Solenoid actuates. Y↓ N→Select Stop. Go to Booklet Knife Control. Check continuity between the Knife Solenoid and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Knife Solenoid (PL 24.58 Item 10). If the problem continues, replace the Booklet PWB (PL 24.51 Item 1). If the problem persists, replace Finisher Main PWB. Select Stop. Select dc330 Component Control [013-140], Booklet Knife Folding Sensor (PL 24.54 Item 3). Select Start. Block/unblock the Knife Folding Sensor. The display changed. Select Stop. Go to Booklet Knife Control. Check continuity between the Knife Folding Sensor and the Booklet PWB and between the Booklet PWB and the Finisher PWB. The continuity check is OK. Y↓ N→Repair the open circuit or short circuit. Replace the Knife Folding Sensor (PL 24.54 Item 3). If the problem continues, replace the Booklet PWB (PL 24.51 Item 1). If the problem persists, replace Finisher Main PWB. Select Stop. If the problem continues, replace the Finisher Main PWB.